Panasonic AJSPX800P AJSPX800 User Guide - Page 91

8-2 SYSTEM SETTING 8-2-1 SYSTEM MODE Items/ Adjustable Data Saved Range Remarks Items/ Adjustable Data Saved Range Remarks REC SIGNAL CAM VIDEO 1394 Select video input signals. CAM Record the signal from the camera VIDEO: Record the signal from the GENLOCK IN terminal 1394: Record the signal from the 1394 input terminal (when the optional unit ACCESS LED ON OFF - CU F E Select whether or not to enable illumination of the P2 card access LEDs. ON: Enable the P2 card access LEDs to light up for card status indications. OFF: LEDs remain off. is attached. *To be supported in the near future.) z After the power has been turned OFF, this setting defaults to CAM when the power is 8-2-2 OPTION MODE turned ON again. z With VIDEO selected, to synchronise this camera-recorder to the video signal (VBS) that is input to the GENLOCK IN terminal, Items/ Adjustable Data Saved Range Remarks - CU F E CAMERA 60i MODE 30P SCU F E the GENLOCK item in [8-2-6 GENLOCK] must be set to EXT. Switch the operating mode of the camera. 60i: Camera operates in 60i mode. 30P: Camera operates in 30P mode. P.OFF GPS DATA HOLD CLEAR Select whether or not to hold the UMID GPS position information while the power is turned off, thereby keeping this information as status data holding the previous value until the power is turned on again, which enables a new measurement to start. V.RES (30P) INTRLCE Set the vertical resolution when the 30p HOLD: Hold and save the data. PROG. mode is selected. INTRLCE: Lines are mixed. Natural images CLEARClear the data when the power is turned off, and save zero (No-Info) 8 can be obtained. from the next power-on until a new PROG. : Lines are not mixed. Complete -CUF - measurement is completed. progressive images can be obtained when images are edited after shooting. SDI METADATA ON OFF -CUF - Select whether or not to output metadata (UMID) to the SDI (when the optional AJYA902AG is attached). When PROG. is selected, images are recorded as progressive segmented frame images, which enables complete progressive editing. However, adding SDI EDH ON OFF -CUF - Select whether or not to add an error detection flag to the SDI output (when the optional AJ-YA902AG is attached). Vertical Detail (V.DTL) produces unnatural SAVE SW (AUD ON Select whether or not to forcibly disable the images. Therefore, we recommend using OUT) OFF audio output when the SAVE ON/OFF the camera with V.DTL set to 0. (Sufficient switch is set to [ON]. vertical response is maintained in the ON: Disable audio output. SCU F E images after the progressive editing even when V.DTL is set to 0.) -CUF - SAVE SW (LCD) ON OFF: Enable audio output. Select whether or not to automatically turn ASPECT 16:9 Select the aspect ratio for recording. OFF off the LCD monitor when the SAVE ON/ 4:3 16:9: Record in aspect ratio. OFF switch is set to [ON]. - CU F E REC MODE 50M 4:3: Record in aspect ratio. Select the recording mode. -CUF - ON: Turn off LCD monitor. OFF: Do not turn off LCD monitor. 25M DV - CU F E SET UP 0% 7.5%A 50M: Record in DVCPRO50 format. 25M: Record in DVCPRO format. DV: Record in DV format. Switch the setup. (When the DVCPRO50 or DVCPRO format is selected.) SAVE SW (SDI) ON OFF -CUF - Select whether or not to automatically disable the SDI output when the SAVE ON/ OFF switch is set to [ON]. ON: Disable SDI output. OFF: Enable SDI output. 0%: Setup is switched to 0% for both the camera output and the recording. 7.5%A: Setup is switched to 7.5% for the camera output and 0% for the The ____ in the Adjustable Range column indicates the preset mode. - CU F E recording. REC TALLY RED GREEN CHAR - CU F E Select the method of displaying the recording status of the camera-recorder when controlling the equipment connected to 1394 (scheduled to be supported soon). The recording status of the connected equipment is displayed by the red tally lamp on the camera-recorder. RED: The red tally lamp lights up. GREEN:The green tally lamp lights up. CHAR: The VF displays [REC] in characters. 91