Pfaff performance 5.2 Manual - Page 23

Bobbin winding

Get Pfaff performance 5.2 PDF manuals and user guides View all Pfaff performance 5.2 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 23 highlights

F Bobbin winding B Winding from horizontal position 1. Place an empty bobbin on the bobbin winder spindle, with the logo facing up. Use only the original PFAFF® bobbins approved for this model. 2. Place the thread spool on the spool pin in horizontal position. Slide a spool cap tightly against the spool. 3. Place the thread into the thread guide (A) from front to back. Pull the thread counter-clockwise above the bobbin winder thread guide (B) and then through the bobbin thread guides (C) at the rear. Note: Make sure the thread is pulled securely inside the pre-tension device for correct thread tension. 4. Thread through the slot in the bobbin (D) from the inside to the outside. 5. Push the bobbin winder spindle to the right to wind. A pop-up appears on the screen to inform you that bobbin winding is active. To adjust winding speed, use the slider in the pop-up. Start bobbin winding by pressing the foot control or touch the start/stop. When the bobbin is full, it will stop winding. Release the foot control or touch start/stop to stop the bobbin winder motor from running. Move the bobbin winder spindle to the left and the pop-up will close. Remove the bobbin and cut the thread using the bobbin thread cutter (F). Winding while threaded Make sure that the presser foot and the needle are in the up position. To prevent the needle from bending, pull the thread out of the needle. E Bring the thread up from the needle thread guide (E), upward through the left-hand threading slot and through the bobbin thread guides (C). Then follow step 4 and 5 above. C A D C A 2:7 Preparations

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
2:7
Preparations
C
D
B
A
Bobbin winding
Winding from horizontal position
1.
Place an empty bobbin on the bobbin winder
spindle, with the logo facing up. Use only the
original PFAFF
®
bobbins approved for this model.
2.
Place the thread spool on the spool pin in
horizontal position. Slide a spool cap tightly
against the spool.
3.
Place the thread into the thread guide (A) from
front to back. Pull the thread counter-clockwise
above the bobbin winder thread guide (B) and
then through the bobbin thread guides (C) at the
rear.
Note: Make sure the thread is pulled securely inside the
pre-tension device for correct thread tension.
4.
Thread through the slot in the bobbin (D) from the
inside to the outside.
5.
Push the bobbin winder spindle to the right to
wind. A pop-up appears on the screen to inform
you that bobbin winding is active. To adjust
winding speed, use the slider in the pop-up. Start
bobbin winding by pressing the foot control or
touch the start/stop.
When the bobbin is full, it will stop winding.
Release the foot control or touch start/stop to stop
the bobbin winder motor from running. Move the
bobbin winder spindle to the left and the pop-up
will close. Remove the bobbin and cut the thread
using the bobbin thread cutter (F).
Winding while threaded
Make sure that the presser foot and the needle are in
the up position. To prevent the needle from bending,
pull the thread out of the needle.
Bring the thread up from the needle thread guide
(E), upward through the left-hand threading slot and
through the bobbin thread guides (C). Then follow
step 4 and 5 above.
F
E
C
A