Ridgid R4512 Owners Manual - Page 37

Making Cuts - operating manual

Get Ridgid R4512 PDF manuals and user guides View all Ridgid R4512 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 37 highlights

OPERATION MAKING CUTS This table saw can perform a variety of cuts that are not all mentioned in this manual. DO NOT attempt to make any cuts not covered here unless you are thoroughly familiar with the proper procedures and necessary accessories. Your local library has many books on table saw usage and specialized woodworking procedures for your reference. The blade provided with the saw is a high-quality combination blade suitable for ripping and cross cut operations. Carefully check all setups and rotate the blade one full revolution to assure proper clearance before connecting saw to power source. Stand slightly to the side of the blade path to reduce the chance of injury should kickback occur. PLACE LEFT HAND ON WORKPIECE AND MITER Gauge HERE CROSS CUT WARNING: Do not use blades rated less than the speed of this tool. Failure to heed this warning could result in personal injury. Use the miter gauge when making cross, miter, bevel, and compound miter cuts. To secure the angle, lock the miter gauge in place by twisting the lock knob clockwise. Always tighten the lock knob securely in place before use. NOTE: It is recommended that you place the piece to be saved on the left side of the blade and that you make a test cut on scrap wood first. To make a cross cut See Figures 57 - 58. WARNING: Make sure the blade guard assembly is installed and working properly to avoid serious possible injury. SWITCH OFF PLACE RIGHT HAND ON MITER Gauge lock knob Fig. 57 SWITCH ON SWITCH COVER NOTE: for clarity, the cover is not shown in the illustrations below. WARNING: Using the rip fence as a cutoff gauge when cross cutting will result in kickback which can cause serious personal injury.  Remove the rip fence.  Set the blade to the correct depth for the workpiece.  Set the miter gauge to 0° and tighten the lock knob.  Make sure the wood is clear of the blade before turning on the saw.  Turn the saw on.  Let the blade build up to full speed before moving the workpiece into the blade. SWITCH IN LOCKED POSITION SWITCH KEY REMOVED NOTE: The front cover does not need to be removed to remove the switch key. Fig. 58  Hold the workpiece firmly with both hands on the miter gauge and feed the workpiece into the blade. Note: The hand closest to the blade should be placed on the miter gauge lock knob and the hand farthest from the blade should be placed on the workpiece.  When the cut is made, turn the saw off. Wait for the blade to come to a complete stop before removing the workpiece. 37

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
37
OPERATION
MAKING CUTS
This table saw can perform a variety of cuts that are not all
mentioned in this manual. DO NOT attempt to make any cuts
not covered here unless you are thoroughly familiar with the
proper procedures and necessary accessories. Your local
library has many books on table saw usage and specialized
woodworking procedures for your reference.
The blade provided with the saw is a high-quality combination
blade suitable for ripping and cross cut operations. Carefully
check all setups and rotate the blade one full revolution to
assure proper clearance before connecting saw to power
source. Stand slightly to the side of the blade path to reduce
the chance of injury should kickback occur.
WARNING:
Do not use blades rated less than the speed of
this tool. Failure to heed this warning could result
in personal injury.
Use the miter gauge when making cross, miter, bevel, and
compound miter cuts. To secure the angle, lock the miter
gauge in place by twisting the lock knob clockwise. Always
tighten the lock knob securely in place before use.
NOTE:
It is recommended that you place the piece to be
saved on the left side of the blade and that you make a test
cut on scrap wood first.
TO MAKE A CROSS CUT
See Figures 57 - 58.
WARNING:
Make sure the blade guard assembly is installed
and working properly to avoid serious possible
injury.
WARNING:
Using the rip fence as a cutoff gauge when cross
cutting will result in kickback which can cause
serious personal injury.
Remove the rip fence.
Set the blade to the correct depth for the workpiece.
Set the miter gauge to 0° and tighten the lock knob.
Make sure the wood is clear of the blade before turning
on the saw.
Turn the saw on.
Let the blade build up to full speed before moving the
workpiece into the blade.
Hold the workpiece firmly with both hands on the miter
gauge and feed the workpiece into the blade.
NOTE:
The hand closest to the blade should be placed
on the miter gauge lock knob and the hand farthest from
the blade should be placed on the workpiece.
When the cut is made, turn the saw off. Wait for the
blade to come to a complete stop before removing the
workpiece.
CROSS CUT
PLACE LEFT HAND ON
WORKPIECE AND
MITER GAUGE HERE
PLACE RIGHT HAND
ON MITER GAUGE
LOCK KNOB
Fig. 57
Fig. 58
SWITCH IN LOCKED
POSITION
SWITCH
OFF
SWITCH
ON
SWITCH KEY REMOVED
SWITCH
COVER
NOTE: for clarity, the cover is not shown
in the illustrations below.
NOTE:
The front cover does not need to be removed
to remove the switch key.