Ridgid R4512 Owners Manual - Page 50

Cleaning The Dust Chute, To Remove And Change Belt

Get Ridgid R4512 PDF manuals and user guides View all Ridgid R4512 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

MAINTENANCE cleaning the dust chute Clean the dust chute periodically to remove sawdust.  Using a 4 mm hex key, remove the screws that secure the back panel.  Inspect the dust chute and attached dust collection devices to clear away sawdust or other debris.  Replace the back panel. TO REMOVE AND CHANGE belt See Figure 79.  Lower the saw blade.  Using a 4 mm hex key, remove the screws that secure the back panel.  With a 6 mm hex key, loosen the bolt above and to the right of the belt.  Pull the belt off the pulleys.  Insert a long flat blade screwdriver as shown.  Holding the screwdriver in place, pull the new belt over both pulleys, making sure it is properly placed.  Remove the screwdriver.  Tighten the bolt. bolt hex key SCREWDRIVER Fig. 79 50

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
50
CLEANING THE DUST CHUTE
Clean the dust chute periodically to remove sawdust.
Using a 4 mm hex key, remove the screws that secure
the back panel.
Inspect the dust chute and attached dust collection
devices to clear away sawdust or other debris.
Replace the back panel.
TO REMOVE AND CHANGE BELT
See Figure 79.
Lower the saw blade.
Using a 4 mm hex key, remove the screws that secure
the back panel.
With a 6 mm hex key, loosen the bolt above and to the
right of the belt.
Pull the belt off the pulleys.
Insert a long flat blade screwdriver as shown.
Holding the screwdriver in place, pull the new belt over
both pulleys, making sure it is properly placed.
Remove the screwdriver.
Tighten the bolt.
MAINTENANCE
SCREWDRIVER
HEX
KEY
BOLT
Fig. 79