Sony HT-SS380 Operating Instructions - Page 26

To cancel Auto Calibration, Confirming/saving the, measurement results - remote code

Get Sony HT-SS380 PDF manuals and user guides
UPC - 027242808317
View all Sony HT-SS380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 26 highlights

The table below provides measurement status shown on the display panel. Measurement for Speaker existance Speaker gain, distance, frequency response Subwoofer gain and distance Display TONE T S P WOOFER To cancel Auto Calibration The Auto Calibration function will be canceled when you perform the following during the measurement process: - Press ?/1 or MUTING. - Press input buttons on the remote control or INPUT +/- on the receiver. - Change the volume level. 3: Confirming/saving the measurement results 1 Confirm the measurement result. When the measurement process is completed, the result appears on the display panel with a beep sound. Measurement process Do this [Display] Completes properly [SAVE EXIT] Proceed to step 2. Fails [E - xxx xx] See "When error codes appear" (page 27). 2 View the measurement result. Press V/v repeatedly to select the item, then press . • EXIT Exits the setting process without saving the measurement results. • WARN CHECK Displays warning related to the measurement results. See "Checking the warning message" (page 27). • SAVE EXIT Saves the measurement results and exits the setting process. • RETRY Performs the Auto Calibration again. 3 Save the measurement result. Select "SAVE EXIT" in step 2. "COMPLETE" appears on the display panel and the measurement results are saved. 4 Disconnect the optimizer microphone from the receiver. Note If you reposition your speaker, we recommend that you perform Auto Calibration again to enjoy the surround sound. 26US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
26
US
The table below provides measurement
status shown on the display panel.
To cancel Auto Calibration
The Auto Calibration function will be
canceled when you perform the following
during the measurement process:
– Press
?
/
1
or MUTING.
– Press input buttons on the remote control or
INPUT +/– on the receiver.
– Change the volume level.
1
Confirm the measurement
result.
When the measurement process is
completed, the result appears on the
display panel with a beep sound.
2
View the measurement result.
Press
V
/
v
repeatedly to select the item,
then press
.
• EXIT
Exits the setting process without saving
the measurement results.
• WARN CHECK
Displays warning related to the
measurement results. See “Checking the
warning message” (page 27).
• SAVE EXIT
Saves the measurement results and exits
the setting process.
• RETRY
Performs the Auto Calibration again.
3
Save the measurement result.
Select “SAVE EXIT” in step 2.
“COMPLETE” appears on the display
panel and the measurement results are
saved.
4
Disconnect the optimizer
microphone from the receiver.
Note
If you reposition your speaker, we recommend that
you perform Auto Calibration again to enjoy the
surround sound.
Measurement for
Display
Speaker existance
TONE
Speaker gain, distance,
frequency response
T S P
Subwoofer gain and
distance
WOOFER
3: Confirming/saving the
measurement results
Measurement process
[Display]
Do this
Completes properly
[SAVE EXIT]
Proceed to step
2.
Fails
[E -
xxx
xx
]
See “When error
codes appear”
(page 27).