Sony HT-SS380 Operating Instructions - Page 27

When error codes appear, To return to step 2 of, 3: Confirming/saving the, measurement results

Get Sony HT-SS380 PDF manuals and user guides
UPC - 027242808317
View all Sony HT-SS380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 27 highlights

Preparing the receiver When error codes appear 1 Check the problem of the error. Display and explanation E - xxx* 32 None of the speakers were detected. Make sure that the optimizer microphone is connected properly and perform the Auto Calibration again. If the optimizer microphone is connected properly but the error code still appears, the optimizer microphone cable may be damaged. E - xxx* 33 • The optimizer microphone is not connected. • None of the front speakers are connected or only one front speaker is connected. • Either the surround left or surround right speaker is not connected. • The subwoofer is not connected. * xxx represent a speaker channel F Front S Surround SW Subwoofer Depending on the error code, the speaker channel may not appears. 2 Perform Auto Calibration again. Press V/v to select "RETRY YES", then press . 3 Follow steps in "3: Confirming/saving the measurement results" (page 26). Checking the warning message If a warning on the measurement result is present, detailed information is displayed. Display and explanation W - xxx* 40 The measurement process has completed with high noise level detection. You may be able to achieve better results if you try in a quite environment again. W - xxx* 41 W - xxx* 42 The input from the microphone is too big. The distance between the speaker and the microphone may be too close. Set them apart and perform the measurement again. W - xxx* 43 The distance and position of a subwoofer cannot be detected. This may be caused by noise. Try to perform the measurement in a quiet environment. NO WARN There is no warning information. * xxx represent a speaker channel FL Front left FR Front right CNT Center SL Surround left SR Surround right SW Subwoofer Depending on the measurement result, the speaker channel may not appears. To return to step 2 of "3: Confirming/saving the measurement results" Press . Tip Depending on the position of the subwoofer, the measurement results may vary. However, there will be no problems even if you continue to use the receiver with that value. 27US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
27
US
Preparing the receiver
When error codes appear
1
Check the problem of the error.
*
xxx
represent a speaker channel
F
Front
S
Surround
SW
Subwoofer
Depending on the error code, the speaker
channel may not appears.
2
Perform Auto Calibration again.
Press
V
/
v
to select “RETRY YES”, then
press
3
Follow steps in “3: Confirming/saving
the measurement results” (page 26).
If a warning on the measurement result is
present, detailed information is displayed.
*
xxx
represent a speaker channel
FL
Front left
FR
Front right
CNT
Center
SL
Surround left
SR
Surround right
SW
Subwoofer
Depending on the measurement result, the speaker
channel may not appears.
To return to step 2 of
“3: Confirming/saving the
measurement results”
Press
Tip
Depending on the position of the subwoofer, the
measurement results may vary. However, there will
be no problems even if you continue to use the
receiver with that value.
Display and explanation
E -
xxx
*
32
None of the speakers were detected. Make sure
that the optimizer microphone is connected
properly and perform the Auto Calibration
again.
If the optimizer microphone is connected
properly but the error code still appears, the
optimizer microphone cable may be damaged.
E -
xxx
*
33
•
The optimizer microphone is not connected.
•
None of the front speakers are connected or
only one front speaker is connected.
•
Either the surround left or surround right
speaker is not connected.
•
The subwoofer is not connected.
Checking the warning message
Display and explanation
W -
xxx
*
40
The measurement process has completed with high
noise level detection.
You may be able to achieve better results if you try
in a quite environment again.
W -
xxx
*
41
W -
xxx
*
42
The input from the microphone is too big. The
distance between the speaker and the microphone
may be too close. Set them apart and perform the
measurement again.
W -
xxx
*
43
The distance and position of a subwoofer cannot be
detected. This may be caused by noise. Try to
perform the measurement in a quiet environment.
NO WARN
There is no warning information.