Sony STR-DA3700ES Operating Instructions - Page 44

MODE and 2CH/A.DIRECT, Release the TONE MODE

Get Sony STR-DA3700ES PDF manuals and user guides View all Sony STR-DA3700ES manuals
Add to My Manuals
Save this manual to your list of manuals

Page 44 highlights

1 Press ?/1 to turn off the receiver. 2 While holding down the TONE MODE and 2CH/A.DIRECT, press ?/1 to turn on the receiver. 3 Release the TONE MODE and 2CH/A.DIRECT after a few seconds. The "CLEARING" appears on the display window for a while, then changes to "CLEARED !" Changes or adjustments made to the settings are now reset to the defaults. Note It takes about one minute for the memory to be cleared completely. Do not turn the receiver off until "CLEARED !" appears on the display. • When you replace or remove the batteries, the programmed codes may be cleared. If this happens, program the remote control codes again (page 118). Inserting batteries into the remote control Insert two R6 (size-AA) batteries in the RM-AAL041 remote control. Observe the correct polarity when installing batteries. RM-AAL041 Notes • Do not leave the remote control in an extremely hot or humid place. • Do not use a new battery with old ones. • Do not mix manganese batteries and other kinds of batteries. • If you do not intend to use the remote control for an extended period of time, remove the batteries to avoid possible damage from battery leakage and corrosion. 44US

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
44
US
1
Press
?
/
1
to turn off the
receiver.
2
While holding down the TONE
MODE and 2CH/A.DIRECT,
press
?
/
1
to turn on the
receiver.
3
Release the TONE MODE and
2CH/A.DIRECT after a few
seconds.
The “CLEARING” appears on the
display window for a while, then changes
to “CLEARED !”
Changes or adjustments made to the
settings are now reset to the defaults.
Note
It takes about one minute for the memory to be
cleared completely. Do not turn the receiver off until
“CLEARED !” appears on the display.
Insert two R6 (size-AA) batteries in the
RM-AAL041 remote control.
Observe the correct polarity when installing
batteries.
Notes
• Do not leave the remote control in an extremely hot
or humid place.
• Do not use a new battery with old ones.
• Do not mix manganese batteries and other kinds of
batteries.
• If you do not intend to use the remote control for an
extended period of time, remove the batteries to
avoid possible damage from battery leakage and
corrosion.
• When you replace or remove the batteries, the
programmed codes may be cleared. If this happens,
program the remote control codes again
(page 118).
Inserting batteries into the
remote control
RM-AAL041