Home » TASCAM Manuals » Audio Mixers » TASCAM DA-6400 » Manual Viewer

TASCAM DA-6400 DA-6400dp Owners Manual - Page 17

– Preparation, Installing an SSD/HDD drive in the case, Loading and removing SSD/HDD cases

Add to My Manuals
Save this manual to your list of manuals

Page 17 highlights

3 - Preparation Installing an SSD/HDD drive in the case 1. While pressing the cover lock on the left side of the SSD/HDD case handle, slide the lower cover toward the connector and remove it. 2. While pressing the cover lock on the right side of the SSD/HDD case handle, slide the upper cover toward the connector and remove it. 3. Place the SSD/HDD drive in the top of the case, and attach it to the connector at the handle end. 4. Attach the set SSD/HDD drive with screws through the bottom of the case. 5. While pressing the cover lock part of the SSD/HDD case, slide the lower and upper covers from the connector end to attach them. NOTE • If you are unable to insert the SSD/HDD case properly, try removing it once and reinserting it. • You can insert a case even when the unit is on. Removing an SSD/HDD case SSD/HDD cases can be ejected. CAUTION Do not remove the SSD/HDD case from the unit when the SSD/HDD is being accessed (during recording, playback, when data is being written or at other times when the SSD/HDD case indicator is blinking orange). Removing a case when its drive is being accessed could cause proper recording to fail, recorded data to be lost, and sudden loud noises from monitoring equipment, which might damage the equipment or harm hearing. NOTE You can remove the SSD/HDD case from the unit even when the unit is on as long as the SSD/HDD is not being accessed (during recording, playback, when data is being written or at other times when the SSD/HDD case indicator is blinking orange). 1. Slide the RELEASE switch toward >. This unlocks the loaded SSD/HDD case so that it can be removed. CAUTION Be careful not to squeeze parts near the handle when attaching the upper and lower covers. Loading and removing SSD/HDD cases Loading an SSD/HDD case Insert the SSD/HDD case into the SSD/HDD SLOT on the front of the unit until they are even. CAUTION Before inserting the SSD/HDD case into the main unit, remove the static electricity protection cover from the SSD/ HDD case main unit connector. Static electricity protection cover 2. While sliding the RELEASE switch toward >, grasp the SDD/HDD case by hand and pull it out. CAUTION After removing the SSD/HDD case from the main unit, attach the static electricity protection cover to the SSD/HDD case main unit connector. Static electricity protection cover Using the security screw You can use the included security screw kit to lock the SDD/HDD case so that cannot be removed. Use a Phillips (+) driver to install/remove the security screw. TASCAM DA-6400/DA-6400dp 17

Section	Page
1 – Introduction	7
Features	7
Included items	7
Conventions used in this manual	7
Trademarks	7
Precautions for placement and use	8
Notes about power supplies	8
Beware of condensation	8
Cleaning the unit	8
Notes about SSD and HDD drives	8
Notes about media	8
Precautions for use	8
Note about formatting	8
Using the TEAC Global Site	8
User registration	8
2 – Names and Functions of Parts	9
Front panel	9
Rear panel	11
Note about the PARALLEL connector	12
Home Screen	12
Menu structure	14
Basic Menu Screen operations	16
Menu operation procedures	16
3 – Preparation	17
Installing an SSD/HDD drive in the case	17
Loading and removing SSD/HDD cases	17
Loading an SSD/HDD case	17
Removing an SSD/HDD case	17
Using the security screw	17
Connecting and disconnecting USB flash drives	18
Installing I/O cards (sold separately)	18
Turning the unit on and off (putting it in standby)	18
Setting the built-in clock date and time	19
Adjusting the brightness	19
Preparing SSD/HDD drives and USB flash drives for use	19
Connecting headphones	20
Setting headphones monitoring mode	20
Setting the lock function	21
4 – Recording	22
Restrictions on recording operations	22
Setting the master clock	22
Making word/video connector settings	23
Setting the reference level	23
Setting input monitoring	23
Setting input monitoring for specific channels	24
Making recording channel settings	24
Setting the record function for specific channels	24
Setting the recording file format	25
Setting the file name format	26
Editing text	26
Automatically incrementing take numbers	27
Incrementing take numbers manually	27
Adding marks automatically when recording	27
Adding marks manually when recording	28
Adding marks when recording	28
Setting the pause mode function	28
Setting input signal routing	28
Making I/O card settings	28
Settings for IF-MA64/EX and IF-MA64/BN cards	29
Timecode synchronized recording	29
Recording duration	29
5 – Working with Folders (BROWSE screen)	30
Opening the BROWSE screen	30
Navigating the BROWSE screen	30
Icons on the BROWSE screen	30
Folder operations	30
Take and file operations	31
Editing folder, take and file names	31
Deleting folders, takes and files	32
Copying folders, takes and files	32
Rebuilding folders	33
Editing the start timecode of a take	33
Creating new folders	33
Folder structure overview	34
Folder structure	34
File name	34
File formats	34
6 – Playback	35
Files that can be played back	35
Basic playback operations	35
Playing recordings	35
Selecting takes	35
Skipping to the previous/next take	35
Selecting takes directly	35
Searching backward and forward	35
Setting the play mode	35
Setting the repeat mode	35
7 – Internal Settings	36
Setting the timecode	36
TC SETUP 1 page settings	36
TC SETUP 2 page settings	37
PARALLEL connector settings	38
PARALLEL INPUT page settings	38
PARALLEL OUTPUT page settings	38
Network function settings	39
Setting the SNTP function	40
Network functions (FTP server/telnet/VNC)	42
FTP (file transfer protocol) server	42
Remote control (Telnet)	43
VNC (virtual network computing)	44
Making oscillator settings	44
8 – Mark and Locate Functions	45
Mark functions	45
Adding marks	45
Using marks	45
Moving to marks	45
Editing mark names	46
Deleting marks	46
Deleting all marks in the current take	46
Editing mark locations	46
Viewing mark information	46
Locating to a specific time	47
Locating before completely specifying the time	47
9 – Loading Files Recorded by Other Devices	48
Preparation before loading	48
Using the loaded files on the unit	48
10 – Data Transfer Using a Computer	49
Computer system requirements	49
Connecting an SSD/HDD to a computer	49
Disconnecting from a computer	50
11 – Other Settings, Information Screens and Keyboard Operations	51
INFO button and indicator appearance	51
Checking the firmware version	51
Firmware update procedures	52
Viewing media information	52
Setting peak hold time	53
Setting the meter mode	53
Using a USB keyboard to operate the unit	53
Setting the keyboard type	53
Using the keyboard to input names and values	53
List of keyboard operations	54
Setting the power redundancy check function (DA-6400dp only)	55
Exporting/importing system backup data	55
Restoring factory default settings	56
12 – Troubleshooting	57
13 – Specifications	58
General	58
Analog output	58
Control input/output	58
Other	58
Dimensional drawings	59
Block diagrams	59
14 – Important notice regarding software	60

Match case Limit results 1 per page

TASCAM DA-6400/DA-6400dp

3 – Preparation

Installing an SSD/HDD drive in the

case

While pressing the cover lock on the left side of the

SSD/HDD case handle, slide the lower cover toward the

connector and remove it.

While pressing the cover lock on the right side of the

SSD/HDD case handle, slide the upper cover toward the

connector and remove it.

Place the SSD/HDD drive in the top of the case, and attach it

to the connector at the handle end.

Attach the set SSD/HDD drive with screws through the

bottom of the case.

While pressing the cover lock part of the SSD/HDD case,

slide the lower and upper covers from the connector end to

attach them.

CAUTION

Be careful not to squeeze parts near the handle when

attaching the upper and lower covers.

Loading and removing SSD/HDD cases

Loading an SSD/HDD case

Insert the SSD/HDD case into the

SSD/HDD SLOT

on the front of

the unit until they are even.

CAUTION

Before

inserting the

SSD/HDD case into the main unit,

remove

the static electricity protection cover from the SSD/

HDD case main unit connector.

Static electricity

protection cover

NOTE

•

If you are unable to insert the SSD/HDD case properly, try

removing it once and reinserting it.

•

You can insert a case even when the unit is on.

Removing an SSD/HDD case

SSD/HDD cases can be ejected.

CAUTION

Do not remove the SSD/HDD case from the unit when the

SSD/HDD is being accessed (during recording, playback,

when data is being written or at other times when the

SSD/HDD case indicator is blinking orange). Removing a

case when its drive is being accessed could cause proper

recording to fail, recorded data to be lost, and sudden loud

noises from monitoring equipment, which might damage

the equipment or harm hearing.

NOTE

You can remove the SSD/HDD case from the unit even when

the unit is on as long as the SSD/HDD is not being accessed

(during recording, playback, when data is being written or

at other times when the SSD/HDD case indicator is blinking

orange).

Slide the

RELEASE

switch toward

This unlocks the loaded SSD/HDD case so that it can be

removed.

While sliding the

RELEASE

switch toward

, grasp the

SDD/HDD case by hand and pull it out.

CAUTION

After removing

the

SSD/HDD case from the main unit,

attach

the static electricity protection cover to the SSD/HDD

case main unit connector.

Static electricity

protection cover

Using the security screw

You can use the included security screw kit to lock the SDD/HDD

case so that cannot be removed.

Use a Phillips (+) driver to install/remove the security screw.