TP-Link RE350 RE350EU V1 User Guide - Page 11

Button Explanation, Position the Extender - reset

Get TP-Link RE350 PDF manuals and user guides View all TP-Link RE350 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 11 highlights

Name WPS 5GHz/ 2.4GHz Power Status Blinking Off On Off On Blinking Off Indication WPS connection is in process. No active connection. The extender is connected to both 2.4GHz and 5GHz Wi-Fi bands of your host network. No connection. The extender is on. The extender is initializing. The extender is off.  WPS Button: If your Wireless router supports WPS or QSS function, you can press the WPS or QSS button and then press the RE button to establish a secure connection between the Wireless router and the extender.  Reset Button: This button is used to restore the extender's factory default settings. There are two ways to reset the extender: Option One: With the extender powered on, use a pin to press the RESET button until all the LEDs turn on momentarily, then release the button and wait the extender to reboot to its factory default settings. Option Two: Restore the default settings from System Tools > Backup &Restore of the extender's Web-based Management page.  LED Button: You can press the LED button to light up or turn off all the LEDs. After the LEDs are off, the extender can still work normally.  Power Button：You can press the Power button to turn on or off the extender.  Ethernet Port: One 10/100/1000Mbps RJ45 Ethernet port is used to add wireless connectivity to an Ethernet-enabled device such as Internet TV, DVR, Gaming console and so on. Please note that this port will not run when it is connected to a router. For safety, we suggest you plug the extender right way up as the picture shown below. Introduction

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
Introduction
Name
Status
Indication
WPS
Blinking
WPS connection is in process.
Off
No active connection.
5GHz/
2.4GHz
On
The extender is connected to both 2.4GHz and
5GHz Wi-Fi bands of your host network.
Off
No connection.
Power
On
The extender is on.
Blinking
The extender is initializing.
Off
The extender is off.
WPS Button:
If your Wireless router supports WPS or QSS function, you
can press the WPS or QSS button and then press the RE button to establish
a secure connection between the Wireless router and the extender.
Reset Button:
This button is used to restore the extender
’
s factory default
settings.
There are two ways to reset the extender:
Option One:
With the extender powered on, use a pin to press the
RESET
button until all the LEDs turn on momentarily, then release the button and
wait the extender to reboot to its factory default settings.
Option Two:
Restore the default settings from
System Tools > Backup
&Restore
of the extender's Web-based Management page.
LED Button:
You can press the LED button to light up or turn off all the
LEDs. After the LEDs are off, the extender can still work normally.
Power Button
：
You can press the Power button to turn on or off the
extender.
Ethernet Port:
One 10/100/1000Mbps RJ45 Ethernet port is used to add
wireless connectivity to an Ethernet-enabled device such as Internet TV,
DVR, Gaming console and so on.
Please note that this port will not run
when it is connected to a router.
For safety, we suggest you plug the extender right way up as the picture shown
below.