Yamaha CLP-611 Owner's Manual - Page 35
Values, Default, Tones and Volumes, Response Time and Attack Length, Procedure, Edit parameters are
![]() |
View all Yamaha CLP-611 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 35 highlights
Subfunctions 6.1 ****** (Organ type) [ Where "******" is replaced by the type name, such as "JAZZ ORGAN1". If the selected type has been edited, a "*" appears after the name.] Values: Default: JAZZ ORGAN1, JAZZ ORGAN2, JAZZ ORGAN3, JAZZ 16 '1', BASIC 16 '8', THEATER 16', OLD ORGAN, WONDERFUL JAZZ ORGAN1 6.2 VoiceEdit (Voice edit settings) Each voice allows you to set independent volumes for eight continuous tones and three decaying attack tones. You can also set a response time (for the continuous tones) and an attack length (for the decay tones). Tones and Volumes Continuous tones Decay tones 4' 2' 5+1/3' 8' 16' 2+2/3' 1+1/3' 1' 4' 2+2/3' 2' 16-foot 8-foot 5+1/3-foot 4-foot 2+2/3-foot 2-foot 1+1/3-foot 1-foot 4-foot 2+2/3-foot 2-foot • The 8-foot stop sets the volume for the fundamental tone. The 4-foot, 2-foot, and 1-foot stops respectively set volumes for the overtones that are one octave, two octaves, and three octaves up. The 16-foot stop sets the volume for the tone that is one octave lower than the fundamental tone. Response Time and Attack Length Volume Continuous Tone Greater response time → Volume Decay Tone Longer attack length → Time Attack length Time Procedure 1 Go to the [6.2 VoiceEdit] screen, and then press SONG SELECT [w] or [v] to move into the editing component. The screen displays a bar graph. Each bar corresponds to a different parameter, and can be set to any of eight levels. 2 You can now use SONG SELECT [w], [v] to move from bar to bar, and the [+/YES] and [-NO] buttons to change the bar levels. The currently selected bar is displayed in blinking mode. 3 When you are finished editing, you can press [t] or [s] to move to another subfunction. ROOM NORMAL MEDIUM BRILLIANCE REVERB EFFECT TOUCH TEMPO Selected bar flashes on and off. 8' 4' 2' 1' 16' 5+1/3' 2+2/3' 1+1/3' Footage Response 4' 2' AtkLength 2+2/3' AtkFootage Each parameter (each bar on the graphic) can be set to any of eight levels. Edit parameters are as follows. Footage 16' (Continuous-tone volume) Footage 8' (Continuous-tone volume) Footage 5+1/3' (Continuous-tone volume) Footage 4' (Continuous-tone volume) Footage 2+2/3' (Continuous-tone volume) Footage 2' (Continuous-tone volume) Footage 1+1/3' (Continuous-tone volume) Footage 1' (Continuous-tone volume) Response (Response time for continuous tones) AtkFootage 4' (Decay-tone) AtkFootage 2+2/3' (Decay-tone) AtkFootage 2' (Decay-tone) AtkLength (Length of decay tones) 6.3 AtkMode (Attack mode) This parameter sets the attack mode for the organ voice selected by subfunction 6.1. Choose either of the following. EACH: Apply attack tones to all notes. (This is the default.) FIRST: Apply attack tones only to the first held note of any note combination (legato sequence). If at least one key is down, all subsequent keys are produced without attack tones. 6.4 RotSP.Spd (Speed of rotary-speaker effect) 6.5 RotSP.Dpt (Depth of rotary-speaker effect) Values: 0,...,20 Default: Varies according to organ type These parameters set up the rotary-speaker effect. The speed setting selects the speaker's rotation speed. The depth setting selects the intensity of the effect. 6.6 ResetOK? (Return to factory defaults.) Press [+/YES] to return all of the edit settings for the selected voice type to their factory defaults. NOTE As a shortcut, you can switch directly into FUNCTION mode's F6.OrganEdit area by holding down the [ORGAN COMBINATION] button and pressing [FUNCTION]. When you are ready to exit from FUNCTION mode, press [FUNCTION] once again. CLP-811/611 Configuration Functions (FUNCTION mode) 31
![](/manual_guide/products/yamaha-clp811-owners-manual-638579e/35.png)