Yamaha DTXTREME Owner's Manual (reference Section) - Page 51

MIDI2] MIDI SETUP2, Ch= Target Channel, Volume, Ctrl# Controller Number, Value, RevSend, ChoSend

Get Yamaha DTXTREME PDF manuals and user guides View all Yamaha DTXTREME manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

REFERENCE SECTION Drum Kit Voice Edit Mode [MIDI2] MIDI SETUP2 Continuing from the [MIDI1] page, specify control change messages on each MIDI channel you want to output when switching from the current drum kit to another. [MIDI2] Volume Pan Ctrl# / Value Ch=10 127 R63 127 127 1 2 3 4 5 1 Ch= (Target Channel) Specify the MIDI channel for sending a MIDI message. ❏Settings: 1 - 16 n First select a MIDI channel here, and then set the contents to send out on that channel using the following parameters. Repeat this procedure for each channel (1 - 16) as necessary. 2 Volume Specify a value for the controller number 007 (volume). ❏Settings: 000 - 127 3 Pan Specify a value for control number 010 (pan). ❏Settings: 000 - 64 -127 (left to center to right) 4 Ctrl# (Controller Number) You can specify any controller number as a control change. Control changes are MIDI messages that can control the performance of a MIDI device. You can specify many kinds of performance using a set of controller numbers and values. Specify the controller number with this parameter, then specify its value with the following Value parameter. ❏Settings: ---, 000 - 127 5 Value Specify the control value with this parameter, according to the previous Ctrl# parameter. ❏Settings: ---, 000 - 127 [MIDI3] MIDI SETUP3 Continuing from the [MIDI2] page, specify the effect send levels on each MIDI channel you want to output when switching from the current drum kit to another. Effect send levels specified here will be sent to the DTXTREME tone generator and output from MIDI OUT except when the MIDI channel is set to "10," the basic channel of the drum kit. As for the MIDI channel 10, the specified effect send levels are only output from MIDI OUT and do not affect the drum kit itself. [MIDI3] RevSend ChoSend Ch=10 127 127 1 2 3 1 Ch= (Target Channel) Specify the MIDI channel for sending a MIDI message. ❏Settings: 1 - 16 n First select a MIDI channel here, and then set the contents to send out on that channel using the following parameters. Repeat this procedure for each channel (1 - 16) as necessary. 2 RevSend Set the send level to the reverb effect (system effect). ❏Settings: 000 - 127 3 ChoSend Set the send level to the chorus effect (system effect). ❏Settings: 000 - 127 51

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
REFERENCE SECTION
Drum Kit Voice Edit Mode
51
[MIDI2] MIDI SETUP2
Continuing from the [MIDI1] page, specify control
change messages on each MIDI channel you
want to output when switching from the current
drum kit to another.
1
Ch= (Target Channel)
Specify the MIDI channel for sending a MIDI
message.
Settings
: 1 – 16
n
First select a MIDI channel here, and then set the
contents to send out on that channel using the
following parameters. Repeat this procedure for each
channel (1 – 16) as necessary.
2
Volume
Specify a value for the controller number 007
(volume).
Settings
: 000 – 127
3
Pan
Specify a value for control number 010 (pan).
Settings
: 000 – 64 –127 (left to center to right)
4
Ctrl# (Controller Number)
You can specify any controller number as a
control change. Control changes are MIDI
messages that can control the performance of a
MIDI device. You can specify many kinds of
performance using a set of controller numbers
and values. Specify the controller number with
this parameter, then specify its value with the
following Value parameter.
Settings
: ---, 000 – 127
5
Value
Specify the control value with this parameter,
according to the previous Ctrl# parameter.
Settings
: ---, 000 – 127
[MIDI3] MIDI SETUP3
Continuing from the [MIDI2] page, specify the
effect send levels on each MIDI channel you
want to output when switching from the current
drum kit to another.
Effect send levels specified here will be sent to
the DTXTREME tone generator and output from
MIDI OUT except when the MIDI channel is set
to “10,” the basic channel of the drum kit. As for
the MIDI channel 10, the specified effect send
levels are only output from MIDI OUT and do
not affect the drum kit itself.
1
Ch= (Target Channel)
Specify the MIDI channel for sending a MIDI
message.
Settings
: 1 – 16
n
First select a MIDI channel here, and then set the
contents to send out on that channel using the
following parameters. Repeat this procedure for each
channel (1 – 16) as necessary.
2
RevSend
Set the send level to the reverb effect (system
effect).
Settings
: 000 – 127
3
ChoSend
Set the send level to the chorus effect (system
effect).
Settings
: 000 – 127
[MIDI2] Volume
Pan
Ctrl#
/ Value
Ch=10
127
R63
127
127
1
4
5
3
2
[MIDI3] RevSend ChoSend
Ch=10
127
127
1
3
2