Yamaha DTXTREME Owner's Manual (reference Section) - Page 88

The Bass or Chord Patterns do Not Play in Pattern or Song Mode

Get Yamaha DTXTREME PDF manuals and user guides View all Yamaha DTXTREME manuals
Add to My Manuals
Save this manual to your list of manuals

Page 88 highlights

The Sound is Too Loud (The Velocity is Permanently Too High) q Lower the gain setting. q Lower the minimum value of the velocity range. q Try another velocity curve. q If you are using a sensor made by other manufacturers, it may be sending a large signal. q Reset the INPUT ATTENUATION switch on the rear panel. The Hi-hat Foot Controller or Footswitch Works Oppositely q Turn the power switch on again with the foot controller or footswitch connected to the rear panel. The DTXTREME will automatically detect the polarity of the switch and enable regular operation. (If the power is currently ON, turn it OFF once and then ON again). q Make sure you are not stepping on the foot controller or footswitch when you turn the power ON. The Bass or Chord Patterns do Not Play in Pattern or Song Mode q Make sure the tracks are not muted. q Make sure the Tr parameter in Song Play mode is not set to "mute." The DTXTREME does Not Receive any Switch or Trigger Data q A data error has occurred. Turn the power OFF and then ON while holding the Play and Trigger buttons and the DTXTREME will reset to its initial settings. Beware that all the data will be lost. Frequent data back-up storage to external MIDI devices such as the Yamaha MDF2 is recommended to prevent lost data. The Sound will Not Stop q Some sounds may have an extremely long release when the Rev Key Off function is enabled. In such a case, press the VOICE button while holding SHIFT to temporarily stop the sound. The Edge Sound is Hard to Produce q You need to use the position sensing RHP120SD pad. 88 APPENDIX

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
88
APPENDIX
The Sound is Too Loud (The Velocity is Permanently Too High)
●
Lower the gain setting.
●
Lower the minimum value of the velocity range.
●
Try another velocity curve.
●
If you are using a sensor made by other manufacturers, it may be sending a large signal.
●
Reset the INPUT ATTENUATION switch on the rear panel.
The Hi-hat Foot Controller or Footswitch Works Oppositely
●
Turn the power switch on again with the foot controller or footswitch connected to the
rear panel. The DTXTREME will automatically detect the polarity of the switch and enable
regular operation. (If the power is currently ON, turn it OFF once and then ON again).
●
Make sure you are not stepping on the foot controller or footswitch when you turn the
power ON.
The Bass or Chord Patterns do Not Play in Pattern or Song Mode
●
Make sure the tracks are not muted.
●
Make sure the Tr parameter in Song Play mode is not set to “mute.”
The DTXTREME does Not Receive any Switch or Trigger Data
●
A data error has occurred. Turn the power OFF and then ON while holding the Play and
Trigger buttons and the DTXTREME will reset to its initial settings. Beware that all the data
will be lost. Frequent data back-up storage to external MIDI devices such as the Yamaha
MDF2 is recommended to prevent lost data.
The Sound will Not Stop
●
Some sounds may have an extremely long release when the Rev Key Off function is
enabled. In such a case, press the VOICE button while holding SHIFT to temporarily stop
the sound.
The Edge Sound is Hard to Produce
●
You need to use the position sensing RHP120SD pad.