Yamaha DTXTREME Owner's Manual (reference Section) - Page 89

Error Messages

Get Yamaha DTXTREME PDF manuals and user guides View all Yamaha DTXTREME manuals
Add to My Manuals
Save this manual to your list of manuals

Page 89 highlights

Error Messages ERROR : MIDI input buffer full push [ENTER] MIDI buffer memory has become full by receiving too much MIDI data at a time via MIDI IN or TO HOST. Reduce the amount of data (data transfer rate) or increase the interval between each transfer on the sending device. ERROR : MIDI data error push [ENTER] An error has occurred while MIDI data was being received. Check if the MIDI cable is properly connected and if the MIDI data is appropriate. ERROR : Host data error push [ENTER] An error has occurred while MIDI data was being received via TO HOST. Check if the MIDI cable is properly connected and the HOST SELECT switch is properly set. ERROR : HOST is offline push [ENTER] Communications via TO HOST are not working. Check if the computer connected to TO HOST is turned on, the serial cable is properly connected to TO HOST, and the HOST SELECT switch is properly set. WARNING: All data initialized push [ENTER] All setting data is initialized because the backup battery inside the DTXTREME may be running short. Consult your nearest Yamaha dealer on replacing the battery. WARNING : Battery voltage is low push [ENTER] The backup battery inside the DTXTREME may be running low. All setting data may be lost if the DTXTREME is turned off after this message is shown. First try to save necessary data to a memory card or so on, then consult your nearest Yamaha dealer on replacing the battery. ERROR : MIDI check sum error push [ENTER] Checksum of the received bulk data is incorrect. Check if the data is not corrupted and appropriate for the DTXTREME, and then retry. ERROR : MIDI Illegal data push [ENTER] Received bulk data contains illegal data. Check if the data is not corrupted and appropriate for the DTXTREME, and then retry. ERROR : Sequencer is Running push [ENTER] This message will be shown if you attempt an operation while the internal sequencer is running. Stop the sequencer and retry. ERROR : Sequence data is not empty push [ENTER] This message will be shown if you attempt recording to operation to the track that contains data. Retry recording to an empty track. APPENDIX 89

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
APPENDIX
89
Error Messages
MIDI buffer memory has become full by
receiving too much MIDI data at a time via MIDI
IN or TO HOST. Reduce the amount of data (data
transfer rate) or increase the interval between
each transfer on the sending device.
An error has occurred while MIDI data was being
received. Check if the MIDI cable is properly
connected and if the MIDI data is appropriate.
An error has occurred while MIDI data was being
received via TO HOST. Check if the MIDI cable is
properly connected and the HOST SELECT
switch is properly set.
Communications via TO HOST are not working.
Check if the computer connected to TO HOST is
turned on, the serial cable is properly connected
to TO HOST, and the HOST SELECT switch is
properly set.
All setting data is initialized because the backup
battery inside the DTXTREME may be running
short. Consult your nearest Yamaha dealer on
replacing the battery.
The backup battery inside the DTXTREME may
be running low. All setting data may be lost if the
DTXTREME is turned off after this message is
shown. First try to save necessary data to a
memory card or so on, then consult your nearest
Yamaha dealer on replacing the battery.
Checksum of the received bulk data is incorrect.
Check if the data is not corrupted and
appropriate for the DTXTREME, and then retry.
Received bulk data contains illegal data. Check if
the data is not corrupted and appropriate for the
DTXTREME, and then retry.
This message will be shown if you attempt an
operation while the internal sequencer is
running. Stop the sequencer and retry.
This message will be shown if you attempt
recording to operation to the track that contains
data. Retry recording to an empty track.
ERROR : MIDI input buffer full
push [ENTER]
ERROR : MIDI data error
push [ENTER]
ERROR : Host data error
push [ENTER]
ERROR : HOST is offline
push [ENTER]
WARNING: All data initialized
push [ENTER]
WARNING : Battery voltage is low
push [ENTER]
ERROR : MIDI check sum error
push [ENTER]
ERROR : MIDI Illegal data
push [ENTER]
ERROR : Sequencer is Running
push [ENTER]
ERROR : Sequence data is not empty
push [ENTER]