Yamaha MMP1 MMP1 Operation Manual [English] - Page 53

Configuring System Settings

Get Yamaha MMP1 PDF manuals and user guides View all Yamaha MMP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

5. Configuring System Settings 5. Configuring System Settings The explanations provided here assume that input from the DAW is sent to the Main Monitor (5.1 ch) and the near field monitor (L/R), and the system supports both Cue output (L/R) and Studio Speaker output (L/R). Once you get used to configuring system settings in the following manner, make the necessary adjustments to settings to match your operating environment. NOTE The MMP1 system treats Main Monitor 1/2 as L and R respectively for some functions. While it is possible to establish a flexible system configuration that is not specialized to any specific format, a system design where Main Monitor 1/2 is interpreted as L/R is recommended. 5-1. Basic settings example This example is based on the system outlined in the following block diagram. Nuendo 5.1 Out (Dante input 1-6) CD (AES/EBU input 1/2) Cue Out Cue Mix Source (Dante input 7/8) Preamp Out (Analog input 1) Preamp Out (Analog input 2) Mixer Talkback (Analog input 3) Director Talkback (Analog input 4) Dim Mute Level Bass Management Mute Talkback Mute Talkback Mute Level Level Level Speaker Set A (Analog output 1-6) Speaker Set B (Analog output 7/8) Headphone (AES/EBU output 5/6) Cue Out (AES/EBU output 1/2) Studio Speaker Out (AES/EBU output 3/4) DAW (Dante output 1) DAW (Dante output 2) 5-1-1. Preparation 1. Launch the MMP1 Editor, and then log in "Offline" mode as an "Administrator." "Administrator" privileges are required to configure settings. 2. Select the sample rate. Settings screen - Scene - MISC MMP1 Operation Manual 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
5. Configuring System Settings
MMP1 Operation Manual
53
5. Configuring System Settings
The explanations provided here assume that input from the DAW is sent to the Main Monitor (5.1 ch) and the near field
monitor (L/R), and the system supports both Cue output (L/R) and Studio Speaker output (L/R). Once you get used to
configuring system settings in the following manner, make the necessary adjustments to settings to match your operating
environment.
NOTE
The MMP1 system treats Main Monitor 1/2 as L and R respectively for some functions. While it is possible to establish a flexible system
configuration that is not specialized to any specific format, a system design where Main Monitor 1/2 is interpreted as L/R is recommended.
5-1. Basic settings example
This example is based on the system outlined in the following block diagram.
5-1-1. Preparation
1.
Launch the MMP1 Editor, and then log in
“Offline” mode as an “Administrator.”
“Administrator” privileges are required to configure
settings.
2.
Select the sample rate.
Settings screen - Scene - MISC
Nuendo 5.1 Out
(Dante input 1-6)
CD
(AES/EBU input 1/2)
Cue Out
Cue Mix Source
(Dante input 7/8)
Preamp Out
(Analog input 1)
Preamp Out
(Analog input 2)
Mixer Talkback
(Analog input 3)
Director Talkback
(Analog input 4)
Speaker Set A
(Analog output 1-6)
Speaker Set B
(Analog output 7/8)
Headphone
(AES/EBU output 5/6)
Cue Out
(AES/EBU output 1/2)
Studio Speaker Out
(AES/EBU output 3/4)
DAW
(Dante output 1)
DAW
(Dante output 2)
Dim
Mute
Level
Bass
Management
Mute
Level
Talkback
Mute
Level
Talkback
Mute
Level