Yamaha MMP1 MMP1 Operation Manual [English] - Page 6

Con basic settings

Get Yamaha MMP1 PDF manuals and user guides View all Yamaha MMP1 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 6 highlights

3-3-2. MMP1 Controller Select an MMP1 on the "Select MMP1" dialog box. The "Select MMP1" dialog box is displayed when launching the MMP1 Controller. NOTE You can also display the "Select MMP1" dialog box from the menu bar to change the desired MMP1 for operation at any time.    Disconnecting from the MMP1  Select the MMP1 connection.  Tap to select the MMP1 to operate.  Tap to connect. NOTE • You can switch between Wireless/Wired on iOS 9.3 or later devices. • You must enter the Passcode for the MMP1 when connecting to an MMP1 with a Passcode set. Entering a passcode is not necessary when connecting to the same MMP1 as that used previously. 3. Setting Up 3-4. Configure basic settings NOTE Only the MMP1 Editor can be used to configure basic settings. Basic settings must be configured on the MMP1 Editor before the MMP1 Controller can be used. 1. Select " (file icon)" on the menu bar, then select "New." 2. Select whether or not you want to use the Setup Wizard. Next, follow the on-screen instructions. When using the Setup Wizard, configure basic settings by answering the questions as they appear on the screen. Canceling the Setup Wizard before it is complete will revert settings to what they were prior to launching the Setup Wizard. When the Setup Wizard is not used, the following values will be applied automatically. Sample Rate 48 kHz Speaker Format Stereo LFE Filter None LFE Trim Bass Management Monitor Source None None None Speaker Set None Cue Mix Input Channel None Cue Mix Output Channel None Talkback Mic Input Channel None MMP1 Operation Manual 6

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
3. Setting Up
MMP1 Operation Manual
6
3-3-2. MMP1 Controller
Select an MMP1 on the “Select MMP1” dialog box. The
“Select MMP1” dialog box is displayed when launching
the MMP1 Controller.
NOTE
You can also display the “Select MMP1” dialog box from the
menu bar to change the desired MMP1 for operation at any time.
1
Select the MMP1 connection.
2
Tap to select the MMP1 to operate.
3
Tap to connect.
NOTE
•
You can switch between Wireless/Wired on iOS 9.3 or later
devices.
•
You must enter the Passcode for the MMP1 when connecting
to an MMP1 with a Passcode set. Entering a passcode is not
necessary when connecting to the same MMP1 as that used
previously.
3-4. Configure basic settings
NOTE
Only the MMP1 Editor can be used to configure basic settings.
Basic settings must be configured on the MMP1 Editor before the
MMP1 Controller can be used.
1.
Select “
(file icon)” on the menu bar, then select
“New.”
2.
Select whether or not you want to use the Setup
Wizard.
Next, follow the on-screen instructions.
When using the Setup Wizard, configure basic settings by
answering the questions as they appear on the screen.
Canceling the Setup Wizard before it is complete will
revert settings to what they were prior to launching the
Setup Wizard.
When the Setup Wizard is not used, the following values
will be applied automatically.
1
3
2
Disconnecting from the MMP1
Sample Rate
48 kHz
Speaker Format
Stereo
LFE Filter
None
LFE Trim
None
Bass Management
None
Monitor Source
None
Speaker Set
None
Cue Mix Input Channel
None
Cue Mix Output Channel
None
Talkback Mic Input Channel
None