Yamaha MT1X Owner's Manual - Page 10
Ff Switch Fast Forward - cassette recorder
View all Yamaha MT1X manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 10 highlights
RECORD SELECT SWITCHES These switches are used to choose the signal to be recorded. The upper left switch is for track 1, the upper right switch is for track 2, the lower left switch is for track 3, and the lower right switch is for track 4. When the track is not to be recording, set the corresponding switch to the OFF position. Switch ON only those switches corresponding to the tracks which are to record. The panel indications for "L" and "R" correspond to the stereo left and right signals, whereas "1", "2","3"and "4" correspond to the signal from the 1, 2, 3, and 4 input channels. Those signals are recorded on their respective track when the switches are in position. NOTE: Tracks 1 and 3 cannot be recorded on the right stereo signal, and tracks 2 and 4 cannot be recorded on the left stereo signal. REC INDICATOR Recording status is indicated in the following three ways: No indication: All tracks 1-4 are not recording. Flashing: All tracks 1-4 are in recording standby mode. By pushing only the REC switch the tape is put into IndthiceatrieocnorOdiNn:g standby mode. All tracks 1-4 are recording, or in the REC pause mode. To resume recording during REC pause, press the PAUSE switch WhReEnCthSiWs sIwTCitHch is pressed, the PLAY switch also moves, and the unit goes into the recording mode. However, if the RECORD SELECT switches for all tracks 1-4 are switched OFF, nothing will be recorded. NOTE: When the REC switch is pressed down, noise occurs which is recorded on the tape. In order to prevent this, we recommended the use of the PAUSE switch Press the PAUSE switch first, then press the REC switch. To start recording, press the PAUSE switch again to shift out of the REC pause mode and into the recording mode. PLAY SWITCH Press this switch for playback. However, if the input selector switch (1) of a track is not in the TAPE position, the sound will not be heard on the stereo buss. REW SWlTCH (REWIND) Use this switch to rewind the tape. Pressing it when the MT1X is in the PLAY mode enables you to hear the sound of the tape while it rewinds. This feature is useful for finding the beginning of a song or other recorded material. FF SWITCH (FAST FORWARD) Use this switch to quickly advance the tape forward. Pressing it when the MT1X is in the PLAY mode enables you to hear the sound of the tape while it is moved forward. This feature is useful for cueing up the start of a subsequent song or other recorded material on the tape. STOP SWITCH Press this to stop tape run. PAUSE SWITCH Press this switch to momentarily stop playback or recording in progress. Press it again to restart. dbx SWITCH Ordinary cassette tapes don't have sufficient dynamic range (the level difference between the softest sounds and the loudest peaks) to adequately record highly dynamic music. If the dbx switch is put "ON" during recording, highly dynamic music signals can be adequately handled, while the hiss noise inherent to cassette tapes is kept down below the range of human hearing. If the dbx switch is kept "ON" during recording, it must also be kept "ON" during playback. DurPinIgTCreHcoCrdOinNg ToRr pOlaLyback, this control can be used to vary the tape running speed from +10% to -10%. The pitch of voices or musical instruments also varies in proportion to tape speed. Under normal conditions, the control should be in the center position. When overdubbing (playing back a recorded passage while recording new material on a different track) the pitch of the previously recorded material can be altered to match the new material if necessary. This feature can also be used to obtain certain special effects during recording. TAPE COUNTER This displays the amount of tape run. RESET SWITCH Press this switch to reset the tape counter to "000". Pressing this switch at the start of recording, or at the beginning of a song, makes it easy to cue up the selection from the start. ZERO STOP SWITCH If this switch is set "ON" during rewinding, the tape will stop when the tape counter reaches "999". During multitrack recording, this feature is convenient for repeated playback or recording operations after rewind. 8