Yamaha MT1X Owner's Manual - Page 14

Power Switch, Dc In Jack, Sync In/sync Out Jacks, Tape Out Jacks, St Out Jacks, Aux Send Jack, Aux - power supply

Get Yamaha MT1X PDF manuals and user guides View all Yamaha MT1X manuals
Add to My Manuals
Save this manual to your list of manuals

Page 14 highlights

POWER SWITCH This switch turns on the MT1X. When switching the unit on or off, make sure that the Input Faders and the AUX RTN Control are at the "0" position. DC IN JACK Connect the supplied AC adaptor to this terminal. To prevent damage, use only the AC adaptor supplied with this unit. SYNC IN/SYNC OUT JACKS These jacks are used during synchronized operation with MIDI-equipped instruments. Use the optional YMC10 MIDI Converter to connect the instruments through these jacks, and set the SYNC switch on the mixer section to "ON". For a detailed explanation, refer to "SyncRecording" on page 33. TAPE OUT JACKS These jacks directly output the signal of each track. During playback, the signals of the tracks being played are output. During recording, the signals of the tracks being recorded are output. Since the output levels cannot be adjusted, set the volume by adjusting the output levels on the instruments themselves. These jacks can be conveniently used in the following ways: Another 4-track recorder can be connected for direct dubbing of all four channels. An external mixer can be connected for mixdown. ST OUT JACKS The mixed signals of each channel (and each track) are output in stereo signal through these jacks. Since these jacks output the final mix, a stereo cassette deck can be connected. These jacks can also be used as follows. The MT1X can be used as a sub-mixer, with the output sent to a main mixer through this jack. A stereo amplifier or powered monitor speakers can be connected through this jack. AUX SEND JACK This jack outputs the mixed signal from the Aux bus, and is used as an output terminal for the connection of an effects device. This can also be used as an additional monitor output. AUX RTN JACKS These jacks are used to input the signal from an effects device back into the MT1X. As well, the mixed output from an external mixer can be connected to these jacks. Please note that if only a single plug is inserted into either one of these jacks, the signal will be sent to both Left and Right channels. This is useful if the effects device being used is mono. 12

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
POWER SWITCH
This switch turns on the MT1X. When switching the unit
on or off, make sure that the Input Faders
and the
AUX RTN Control
are at the “0” position.
DC IN JACK
Connect the supplied AC adaptor to this terminal. To pre-
vent damage, use only the AC adaptor supplied with this
unit.
SYNC IN/SYNC OUT JACKS
These jacks are used during synchronized operation with
MIDI-equipped instruments. Use the optional YMC10
MIDI Converter to connect the instruments through
these jacks, and set the SYNC switch on the mixer sec-
tion to “ON”. For a detailed explanation, refer to “Sync-
Recording” on page 33.
TAPE OUT JACKS
These jacks directly output the signal of each track. Dur-
ing playback, the signals of the tracks being played are
output. During recording, the signals of the tracks be-
ing recorded are output. Since the output levels cannot
be adjusted, set the volume by adjusting the output levels
on the instruments themselves. These jacks can be con-
veniently used in the following ways:
Another 4-track recorder can be connected for direct
dubbing of all four channels.
An external mixer can be connected for mixdown.
ST OUT JACKS
The mixed signals of each channel (and each track) are
output in stereo signal through these jacks. Since these
jacks output the final mix, a stereo cassette deck can
be connected. These jacks can also be used as follows.
The MT1X can be used as a sub-mixer, with the out-
put sent to a main mixer through this jack.
A stereo amplifier or powered monitor speakers can
be connected through this jack.
AUX SEND JACK
This jack outputs the mixed signal from the Aux bus, and
is used as an output terminal for the connection of an
effects device. This can also be used as an additional
monitor output.
AUX RTN JACKS
These jacks are used to input the signal from an effects
device back into the MT1X. As well, the mixed output
from an external mixer can be connected to these jacks.
Please note that if only a single plug is inserted into either
one of these jacks, the signal will be sent to both Left
and Right channels. This is useful if the effects device
being used is mono.
12