Brother International BAS-760 Instruction Manual - English - Page 28

back,total

Get Brother International BAS-760 PDF manuals and user guides View all Brother International BAS-760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 28 highlights

El Command list • Refer to this command list for using exact commands when programming. 111 END 2 2 2 E DATA CLEAR 2 LI Sri DOUBLE-ROW SEWING (Specify the width.) 555O TRACE 7 7 7 0 PARALLEL SHIFT El] SMOOTHING Ex. 030M: A stitch length of 3 mm (Specify the stitch If not specified: 3 mm length.) 7 8 9 O SMOOTHING END (Be sure to press at a corner stitch position. ) 9Y YU 111Y=01-10 NEEDLE ZIGZAG OPERATION En is X direction stitch length 4 4 4E 4 4 5 El 6 2 0 El 6 2 10 Y feed timing change Reset for 444Li Low speed changeover 2,000 spm (2 forward, 2 back, total 5 needles) Reset for 620 El 6 2 5O 6 2 6E 6 3 0O 6 3 10 Low speed changeover 2,500 spm (2 forward, 2 back,total 5 needles) Reset for 625 n Low speed changeover 3,000 spm (1 forward, 1 back, total 3 needles) Reset for 630 X Specify TRACE first when using TRACE and other commands, such as SMOOTHING, at the same time. X To program the above commands (enclosed in the box), first program the sewing data once, send by means of the programmer as far as the necessary points, and then input. ID Programmer connection (1) Turn power switch 0 to OFF and connect programmer plug @ to the connector on the front cover. (2) Turn power switch 0 to ON. Set the sewing damp assembly in the shunting position. Press the (program) key. The sewing clamp assembly will come down and the program mode will be established. Insert a piece of material under the assembly to facilitate its movement. (3) On completion of programming, press the (program) key to switch to the sewing mode. X Do not press the panel keys of the programmer unit with finger nails or other pointed objects.

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
El
Command
list
•
Refer
to
this
command
list
for
using
exact
commands
when
programming.
1
1
1
END
2 2 2
E
DATA
CLEAR
2
LI
Sri
DOUBLE
-ROW
SEWING
(Specify
the
width.)
555O
TRACE
7
7
7
0
PARALLEL
SHIFT
El]
SMOOTHING
Ex.
030M:
A
stitch
length
of
3
mm
(Specify
the
stitch
If
not
specified:
3
mm
length.)
7
8
9
O
SMOOTHING
END
(Be
sure
to
press
at
a
corner
stitch
position.
)
9Y
YU
111Y=01-10
NEEDLE
ZIGZAG
OPERATION
En
is
X
direction
stitch
length
4 4
4
E
Y
feed
timing
change
6
2
5
O
Low
speed
changeover
2,500
spm
4 4
5
El
Reset
for
444
Li
(2
forward,
2
back,total
6
2
0
El
Low
speed
changeover
5
needles)
2,000
spm
6
2
6
E
Reset
for
625
n
(2
forward,
2
back,
total
5
needles)
6
3
0
O
Low
speed
changeover
3,000
spm
6
2
1
0
Reset
for
620
El
(1
forward,
1
back,
total
3
needles)
6
3
1
0
Reset
for
630
X
Specify
TRACE
first
when
using
TRACE
and
other
commands,
such
as
SMOOTHING,
at
the
same
time.
X
To
program
the
above
commands
(enclosed
in
the
box),
first
program
the
sewing
data
once,
send
by
means
of
the
programmer
as
far
as
the
necessary
points,
and
then
input.
ID
Programmer
connection
(1)
Turn
power
switch
0
to
OFF
and
connect
programmer
plug
@
to
the
connector
on
the
front
cover.
(2)
Turn
power
switch
0
to
ON.
Set
the
sewing
damp
assembly
in
the
shunting
position.
Press
the
(program)
key.
The
sewing
clamp
assembly
will
come
down
and
the
program
mode
will
be
established.
Insert
a
piece
of
material
under
the
assembly
to
facilitate
its
movement.
(3)
On
completion
of
programming,
press
the
(program)
key
to
switch
to
the
sewing
mode.
X
Do
not
press
the
panel
keys
of
the
programmer
unit
with
finger
nails
or
other
pointed
objects.
<99
—25-