Brother International BAS-760 Instruction Manual - English - Page 50

Stacker, position, adjustment

Get Brother International BAS-760 PDF manuals and user guides View all Brother International BAS-760 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 50 highlights

Removal of the movable knife // 0 1. Remove clamping screw 0 and then presser foot assembly @. 2. Turn the pulley and stop the needle bar at its highest position. 3. Remove clamping screws @ and then bottom-plunger 0. O. 4. Push thread trimming rod in the arrowed direction and stop where flat-head screws @ can be seen. 5. Remove flat-head screws @ and then movable knife Note 1: Remove bottom-plunger 0 and movable knife f) after removing the needle. Note 2: To reassemble, reverse the above procedures. CI Stacker position adjustment 1. Release the air. Loosen bolt 0 and adjust stacker table @ to the best position. Conduct this with cylinder @ retracted. 2. Tighten bolt O. 3. Make sure that the stacker table @ will contact cover 0 when it is pushed toward cover 0. 4. Loosen the four bolts and adjust the height of stacker table @ so that the front pieces will be in a well-balanced stack. 5. Tighten bolts®. 6. Loosen bolt O and adjust the height of presser bar O. 7. Tighten bolt O. -47-

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
Removal
of
the
movable
knife
//
0
1.
Remove
clamping
screw
0
and
then
presser
foot
assembly
@.
2.
Turn
the
pulley
and
stop
the
needle
bar
at
its
highest
position.
3.
Remove
clamping
screws
@
and
then
bottom
-plunger
0.
4.
Push
thread
trimming
rod
in
the
arrowed
direction
and
stop
where
flat
-head
screws
@
can
be
seen.
5.
Remove
flat
-head
screws
@
and
then
movable
knife
O.
Note
1:
Remove
bottom
-plunger
0
and
movable
knife
f)
after
removing
the
needle.
Note
2:
To
reassemble,
reverse
the
above
procedures.
CI
Stacker
position
adjustment
1.
Release
the
air.
Loosen
bolt
0
and
adjust
stacker
table
@
to
the
best
position.
Conduct
this
with
cylinder
@
retracted.
2.
Tighten
bolt
O.
3.
Make
sure
that
the
stacker
table
@
will
contact
cover
0
when
it
is
pushed
toward
cover
0.
4.
Loosen
the
four
bolts
and
adjust
the
height
of
stacker
table
@
so
that
the
front
pieces
will
be
in
a
well-balanced
stack.
5.
Tighten
bolts®.
6.
Loosen
bolt
O
and
adjust
the
height
of
presser
bar
O.
7.
Tighten
bolt
O.
-47-