Cisco AIR-AP521G-A-K9 Configuration Guide - Page 34

Previous, Finish, Step 9 Summary Window - review

Get Cisco AIR-AP521G-A-K9 - 521 Wireless Express Access Point PDF manuals and user guides
UPC - 882658161988
View all Cisco AIR-AP521G-A-K9 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 34 highlights

Adding a New Controller Chapter 2 Adding a WLC526 Controller and LAP521 Access Points Step 9 For the management interface, perform these operations: a. Enter the IP address of the management interface. b. Accept the default subnet mask or enter a new subnet mask in the Subnet Mask field. c. Enter the IP address of the default gateway (or router) in the Default Gateway field. Note The VLAN identifier is set to 0 for an untagged VLAN. This setting cannot be changed with the CCA. This setting must be the same on the switch. d. Accept the default controller port 1 setting or click the drop-down arrow to choose port 2. These ports are located on the controller front panel and are used to connect the controller to the network. e. Enter the IP address of the DHCP server in the DHCP Server IP Address field. Note The default for the Transport Mode is Layer 3 and cannot be changed with the CCA. f. For the AP Manager interface, enter the IP address for the AP Manager in the IP Address field. g. Click Next and the Step 9 Summary window appears (see Figure 2-11). Figure 2-11 Step 9 Summary Window Step 10 Carefully review the summary settings and perform one of these operations: a. If the summary is incorrect or you desire to make changes, click Previous and the previous window appears. b. If the summary is correct, click Finish and the wizard begins to transfer the configuration information to the controller (a progress bar appears). When the transfer is complete, the wizard indicates the finish status on the window (see Figure 2-12). Cisco 500 Series Wireless Express Mobility Controller Configuration Guide 2-8 OL-15283-01

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
2-8
Cisco 500 Series Wireless Express Mobility Controller Configuration Guide
OL-15283-01
Chapter 2
Adding a WLC526 Controller and LAP521 Access Points
Adding a New Controller
Step 9
For the management interface, perform these operations:
a.
Enter the IP address of the management interface.
b.
Accept the default subnet mask or enter a new subnet mask in the Subnet Mask field.
c.
Enter the IP address of the default gateway (or router) in the Default Gateway field.
Note
The VLAN identifier is set to 0 for an untagged VLAN. This setting cannot be changed with
the CCA. This setting must be the same on the switch.
d.
Accept the default controller port 1 setting or click the drop-down arrow to choose port 2. These
ports are located on the controller front panel and are used to connect the controller to the network.
e.
Enter the IP address of the DHCP server in the DHCP Server IP Address field.
Note
The default for the Transport Mode is Layer 3 and cannot be changed with the CCA.
f.
For the AP Manager interface, enter the IP address for the AP Manager in the IP Address field.
g.
Click
Next
and the Step 9 Summary window appears (see
Figure 2-11
).
Figure 2-11
Step 9 Summary Window
Step 10
Carefully review the summary settings and perform one of these operations:
a.
If the summary is incorrect or you desire to make changes, click
Previous
and the previous window
appears.
b.
If the summary is correct, click
Finish
and the wizard begins to transfer the configuration
information to the controller (a progress bar appears). When the transfer is complete, the wizard
indicates the finish status on the window (see
Figure 2-12
).