D-Link DES-3326S Reference Manual
D-Link DES-3326S - Switch - Stackable Manual
 |
UPC - 790069242755
View all D-Link DES-3326S manuals
Add to My Manuals
Save this manual to your list of manuals |
D-Link DES-3326S manual content summary:
- D-Link DES-3326S | Reference Manual - Page 1
DES-3326SR Layer 3 Switch Command Line Interface Reference Manual (April 2003) DES3326SR... 1 Printed In Taiwan RECYCLABLE i - D-Link DES-3326S | Reference Manual - Page 2
von ungeeigneten Ersatzteilen kann eine weitere Beschä digung hervorrufen. 17. Wenden Sie sich mit allen Fragen die Service und Repartur betreffen an Ihren Servicepartner. Somit stellen Sie die Betriebssicherheit des Gerä tes sicher. 18. Zum Netzanschluß dieses Gerä tes ist eine geprüfte Leitung zu - D-Link DES-3326S | Reference Manual - Page 3
service for a period commencing on the date of purchase from D-Link or its Authorized Reseller and extending for the length of time stipulated by the Authorized Reseller or D-Link D-Link office within ninety (90) days of purchase. A list of D-Link offices is provided at the back of this manual, - D-Link DES-3326S | Reference Manual - Page 4
D-Link with all costs of mailing/shipping/insurance prepaid. D-Link shall never be responsible for any software, firmware, service for software products may be obtained by contacting a D-Link office within the applicable warranty period. A list of D-Link offices is provided at the back of this manual - D-Link DES-3326S | Reference Manual - Page 5
product's Registration Card, provided at the back of this manual, must be sent to a D-Link office. To obtain an RMA number for warranty service as to a hardware product, or to obtain warranty service as to a software product, contact the D-Link office nearest you. An address/telephone/fax/e-mail/Web - D-Link DES-3326S | Reference Manual - Page 6
environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with this user's guide, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference - D-Link DES-3326S | Reference Manual - Page 7
9 Using the Console CLI 13 Command Syntax 19 Basic Switch Commands 24 Switch Port Commands 46 Network Management Commands 54 Download/Upload Commands QOS Commands 151 Port Mirroring Commands 167 VLAN Commands 174 Link Aggregation Commands 187 IP Interface Commands 195 Arp Commands 208 vii - D-Link DES-3326S | Reference Manual - Page 8
Commands 233 IGMP Snooping Commands 239 Bootp Relay Commands 255 DNS Relay Commands 262 RIP Commands 273 DVMRP Commands 281 IP Multicasting Commands 292 MD5 Configuration Commands 296 OSPF Configuration Commands 301 Command History List 342 Technical Specifications 348 Index 352 viii - D-Link DES-3326S | Reference Manual - Page 9
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 1 INTRODUCTION The switch can be managed through the switch's serial port, Telnet, or the Web-based management agent. The Command Line Interface (CLI) can be used to configure and manage the switch via the serial port or Telnet interfaces. - D-Link DES-3326S | Reference Manual - Page 10
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Fig. 1- 1. Initial Console screen. There is no initial username or password. Just press the Enter key twice to display the CLI input cursor − DES-3326SR:4#. This is the command line where all commands are input. Setting the Switch's IP - D-Link DES-3326S | Reference Manual - Page 11
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual The switch's MAC address can also be found from the Web management program on the Switch Information (Basic Settings) window on the Configuration menu. The IP address for the switch must be set before it can be managed with the Web-based - D-Link DES-3326S | Reference Manual - Page 12
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Fig. 1- 4. Assigning the Switch an IP Address In the above example, the switch was assigned an IP address of 10.52.19.7 with a subnet mask of 255.0.0.0. The system message Success indicates that the command was executed successfully. The - D-Link DES-3326S | Reference Manual - Page 13
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 2 USING THE CONSOLE CLI The DES-3326SR supports a console management interface that allows the user to connect to the switch's management agent via a serial port and a terminal or a computer running a terminal emulation program. The - D-Link DES-3326S | Reference Manual - Page 14
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual • VT-100/ANSI compatible • 9,600 baud • 8 data bits • No parity • One stop bit • No flow control You can also access the same functions over a Telnet interface. Once you have set an IP address for your Switch, you can use a Telnet program - D-Link DES-3326S | Reference Manual - Page 15
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Fig. 2- 2. The ? Command The dir command has the same function as the ? command. When you enter a command without its required parameters, the CLI will prompt - D-Link DES-3326S | Reference Manual - Page 16
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual (config account) at the command prompt. Now the appropriate User name can be entered and the config account command re-executed addition, the syntax of the help prompts are the same as presented in this manual − angle brackets < > indicate - D-Link DES-3326S | Reference Manual - Page 17
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Fig. 2- 5. The Next Available Commands Prompt The top-level commands consist of commands like show or config. Most of these commands require one or more - D-Link DES-3326S | Reference Manual - Page 18
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual In the above example, all of the possible next parameters for the show command are displayed. At the next command prompt, the up arrow was used to re-enter the show command, followed by the account parameter. The CLI then displays the user - D-Link DES-3326S | Reference Manual - Page 19
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 3 COMMAND SYNTAX The following symbols are used to describe how command entries are made and values and arguments are specified in this manual. The online help must supply an IP interface name in the space, a VLAN name in the - D-Link DES-3326S | Reference Manual - Page 20
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual [square brackets] Purpose Encloses a required value or set of required arguments. One or more values or arguments can be specified. Syntax create account [admin/user] Description In the above syntax example, you must specify either - D-Link DES-3326S | Reference Manual - Page 21
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual / slash Command {braces} Purpose Syntax Description Example command [enabled/disabled]} In the above syntax example, you must choose to enter an IP interface name in the space or all, but version , query_interval - D-Link DES-3326S | Reference Manual - Page 22
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Line Editing Key Usage De le t e In certain formats, deletes highlighted characters and then shifts the remaining characters in the line to the left. Backspace Deletes the character to the - D-Link DES-3326S | Reference Manual - Page 23
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Line Editing Key Usage p Displays the previous page. q Stops the display of remaining pages when multiple pages are to be displayed. r Refreshes the pages currently - D-Link DES-3326S | Reference Manual - Page 24
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 4 BASIC SWITCH COMMANDS The basic switch commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create account [admin/user] config account - D-Link DES-3326S | Reference Manual - Page 25
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create account Purpose Used to create user accounts Syntax create [admin/user] Description The create account command is used to create user accounts that consist of a username of 1 to 15 characters and a password of 0 to - D-Link DES-3326S | Reference Manual - Page 26
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config account Purpose Used to configure user accounts Syntax config account Description The config account command configures a user account that has been created using the create account command. Parameters - D-Link DES-3326S | Reference Manual - Page 27
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show account Purpose Syntax Description Used to display user accounts show account Displays all user accounts created on the switch. Up to 8 user accounts can exist on the switch at one time. Parameters Restrictions none. none. - D-Link DES-3326S | Reference Manual - Page 28
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete account Purpose Syntax Description Used to delete an existing user account delete account The delete account command deletes a user account that has been created using the create account command. Parameters - D-Link DES-3326S | Reference Manual - Page 29
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show session Purpose Used to display a list of currently logged-in users. Syntax show session Description This command displays a list of all the users that are logged-in at the time the command is issued. Parameters None - D-Link DES-3326S | Reference Manual - Page 30
switch Command: show switch Device Type : DES-3326SR Fast-Ethernet Switch Ext. Ports : 1000TX + 1000TX MAC Address : 00-01-02-03-04-00 IP Address : 10.90.90.90 (Manual) VLAN Name : default Subnet Mask : 255.0.0.0 Default Gateway : 0.0.0.0 Boot PROM Version : Build 1.00.001 Firmware - D-Link DES-3326S | Reference Manual - Page 31
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Spanning Tree GVRP IGMP Snooping TELNET WEB RMON DES-3326SR:4# : Disabled : Disabled : Disabled : Enabled (TCP 23) : Enabled (TCP 80) : Disabled Basic Switch Commands 31 - D-Link DES-3326S | Reference Manual - Page 32
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show serial_port Purpose Used to display the current serial port settings. Syntax show serial_port Description This command displays the current serial port settings. Parameters none. - D-Link DES-3326S | Reference Manual - Page 33
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config serial_port Purpose Used to configure the user input. 2_minutes − The console will log out the current user if there is no user input for 2 minutes. 5_minutes − The console will log out the current user if there is no user - D-Link DES-3326S | Reference Manual - Page 34
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure baud rate: DES-3326SR:4#config serial_port baud_rate 9600 Command: config serial_port baud_rate 9600 Success. DES-3326SR:4# 34 Basic Switch Commands - D-Link DES-3326S | Reference Manual - Page 35
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual default setting is enabled. Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To enable pausing of the screen display when show command output reaches the end of the page: DES-3326SR - D-Link DES-3326S | Reference Manual - Page 36
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual users can issue this command. Example Usage: To disable pausing of the screen display when show command output reaches the end of the page: DES-3326SR:4#disable clipaging Command: disable clipaging Success. DES-3326SR:4# 36 Basic Switch - D-Link DES-3326S | Reference Manual - Page 37
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable telnet Purpose Used to enable communication with and management of the switch using the Telnet protocol. Syntax enable telnet Description This command is used to enable the Telnet protocol on the switch. The - D-Link DES-3326S | Reference Manual - Page 38
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable telnet Purpose Used to disable the Telnet protocol on the switch. Syntax disable telnet Description This command is used to disable the Telnet protocol on the switch. Parameters none. Restrictions Only administrator- - D-Link DES-3326S | Reference Manual - Page 39
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable web Purpose Syntax Description Used to enable the HTTP-based management software on the switch. enable web This command is used to enable the Webbased management software on the switch. The user can specify the - D-Link DES-3326S | Reference Manual - Page 40
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable web Purpose Used to disable the HTTP-based management software on the switch. Syntax disable web Description This command disables the Web-based management software on the switch. Parameters none. Restrictions Only - D-Link DES-3326S | Reference Manual - Page 41
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual sav e Purpose Syntax Description Parameters Restrictions Used to save changes in the switch's configuration to non-volatile RAM. Sav e This command is used to enter the current switch configuration into non-volatile RAM. The saved switch - D-Link DES-3326S | Reference Manual - Page 42
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual reboot Purpose Syntax Description Parameters Restrictions Used to restart the switch. reboot This command is used to restart the switch. none. none. Example Usage: To restart the switch: DES-3326SR:4#reboot Command: reboot Are you sure - D-Link DES-3326S | Reference Manual - Page 43
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual reset Purpose Syntax Description Parameters Restrictions Used to reset the switch to the factory default settings. reset {config/system} This command is used to restore the switch's configuration to the default settings assigned from the - D-Link DES-3326S | Reference Manual - Page 44
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual DES-3326SR:4#reset config Command: reset config Success. DES-3326SR:4# login Purpose Syntax Description Parameters Restrictions Used to log in a user to the switch's console. login This command is used to initiate the login procedure. - D-Link DES-3326S | Reference Manual - Page 45
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual logout Purpose Syntax Description Parameters Restrictions Used to log out a user from the switch's console. logout This command terminates the current user's session on the switch's console. none. none. Example Usage: To terminate the - D-Link DES-3326S | Reference Manual - Page 46
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 5 SWITCH PORT COMMANDS The switch port commands in the Command Line Interface (CLI) are listed (along with the portlist/all> show port_security Each command is listed, in detail, in the following sections. 46 Switch Port Commands - D-Link DES-3326S | Reference Manual - Page 47
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ports Purpose Used to configure the switch's Ethernet port settings. Syntax config ports [] { spe e d[aut o /1 0 _half /1 0 _f ull/1 0 0 _half /1 0 0 _hal f/1000_full] learning [enabled/disabled] state [enabled/ - D-Link DES-3326S | Reference Manual - Page 48
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ports the MAC address learning on the specified range of ports. state [enabled/disabled] − Enables or disables the specified range of ports. Restrictions Only administrator-level users can issue this command. Example Usage: To - D-Link DES-3326S | Reference Manual - Page 49
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config port_security Purpose Used to configure port lock settings. Syntax config port_security /all admin_state [enabled/disaled] max_learning_addr lock_address_mode [De le t e OnT i m o ut /De le t e OnR e se t ] - D-Link DES-3326S | Reference Manual - Page 50
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config port_security reset or rebooti. Restrictions Only administrator-level users can issue this command. Example Usage: To configure the port lock for ports 1:12 - 1:14 to delete the dynamic address table entries on timeout: DES-3326SR - D-Link DES-3326S | Reference Manual - Page 51
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ports Purpose Syntax Description Parameters Used to display the current configuration of a range of ports. show ports {} This command is used to display - D-Link DES-3326S | Reference Manual - Page 52
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 5 Enabled 6 Enabled 7 Enabled Auto Auto Auto Link Down Link Down Link Down Enabl ed Enabled Enabled show port_security Purpose Used to display the current portr lock configuration. Syntax show port_security {} - D-Link DES-3326S | Reference Manual - Page 53
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the port lock configuration: DES-3326SR:4#show port_security Command: show port_security Port# Admin State Max. Learning Addr. Lock Address Mode 1 Disabled 1 DeleteOnReset 2 Disabled 1 DeleteOnReset 3 - D-Link DES-3326S | Reference Manual - Page 54
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 6 NETWORK MANAGEMENT COMMANDS The network management commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. The DES-3326SR supports the Simple Network Management Protocol ( - D-Link DES-3326S | Reference Manual - Page 55
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command Parameters create snmp user delete snmp user show snmp user show snmp groups create snmp view delete snmp view show snmp view create snmp community delete snmp community show snmp community config snmp engineID show - D-Link DES-3326S | Reference Manual - Page 56
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete snmp group create snmp host delete snmp host show snmp host enable rmon disable rmon ping traceroute config mac_notification enable mac_notification show mac_notification notify_view < - D-Link DES-3326S | Reference Manual - Page 57
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp user Purpose Used to create a new SNMP user and adds the user to an SNMP group that is also created by this command. Syntax create snmp user be used. The SNMP v2c supports both centralized and distributed network management - D-Link DES-3326S | Reference Manual - Page 58
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp user v3 - Specifies that the SNMP version 3 will be to prevent it being seen by an unauthorized source. encrypted - Specifies that the password will be in an encrypted format. auth [md5/sha] - Initiate an authenticationlevel - D-Link DES-3326S | Reference Manual - Page 59
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp user host sends to the agent. Restrictions Only administrator-level users can issue this command. Example Usage: To create an SNMP user on the switch: DES-3326SR:4#create snmp user dlink default v3 encrypted auth md5 - D-Link DES-3326S | Reference Manual - Page 60
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete snmp user Purpose Used to remove an SNMP user from an SNMP group and also to delete the associated SNMP group. Syntax delete snmp user Description The delete snmp user command removes an SNMP user from its SNMP - D-Link DES-3326S | Reference Manual - Page 61
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp user Purpose Used to display information about each SNMP username in the SNMP group username table. Syntax Description show snmp user The show snmp user command displays information about each SNMP username in the SNMP group - D-Link DES-3326S | Reference Manual - Page 62
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp groups Purpose Used to display the group-names of SNMP groups currently configured on the switch. The security model, level, and status of each group is also displayed. Syntax Description show snmp groups The show snmp - D-Link DES-3326S | Reference Manual - Page 63
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Group Name : Group4 ReadView Name : ReadView WriteView Name : WriteView Notify View Name : NotifyView Securiy Model : SNMPv3 Securiy Level : authNoPriv Group Name : Group5 ReadView Name : ReadView - D-Link DES-3326S | Reference Manual - Page 64
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Notify View Name : restricted Securiy Model : SNMPv3 Securiy Level : NoAuthNoPriv Group Name : ReadGroup ReadView Name : CommunityView WriteView Name : Notify View Name : CommunityView Securiy Model : SNMPv1 - D-Link DES-3326S | Reference Manual - Page 65
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual DES-3326SR:4# create snmp view Purpose Used to assign views to community strings to list of objects that an SNMP manager can access. Restrictions Only administrator-level users can issue this command. Network Management Commands 65 - D-Link DES-3326S | Reference Manual - Page 66
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To create and SNMP view: DES-3326SR:4#create snmp view dlinkview 1.3.6 view_type included Command: create snmp view dlinkview 1.3.6 view_type included Success. DES-3326SR:4# 66 Network Management Commands - D-Link DES-3326S | Reference Manual - Page 67
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete snmp view Purpose Syntax Description Parameters Used to remove an SNMP view entry previously created on the switch. delete snmp view [all/] The delete snmp view command is used to remove an SNMP view - D-Link DES-3326S | Reference Manual - Page 68
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp view Purpose Used to display an SNMP view previously created on the switch. Syntax show snmp view {} Description The show snmp view command displays an SNMP view previously created on the switch. Parameters - D-Link DES-3326S | Reference Manual - Page 69
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual restricted 1.3.6.1.6.3.15.1.1 CommunityView 1 CommunityView 1.3.6.1.6.3 CommunityView .3.6.1.6.3.1 Total Entries: 11 DES-3326SR:4# Included Included Excluded Included Network Management Commands 69 - D-Link DES-3326S | Reference Manual - Page 70
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp community Purpose Used to create an SNMP community string to define the relationship between the SNMP manager and an agent. The community string acts like a password to permit access to the agent on the switch. One or more - D-Link DES-3326S | Reference Manual - Page 71
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp community remote SNMP managers access to MIB objects in the switch's SNMP agent. − An alphanumeric string of up to 32 characters that is used to identify the group of MIB objects that a remote SNMP - D-Link DES-3326S | Reference Manual - Page 72
is used like a password to give remote SNMP managers access to MIB objects in the switch's SNMP agent. Restrictions Only administrator-level users can issue this command. Example Usage: To delete the SNMP community string "dlink:" DES-3326SR:4#delete snmp community dlink Command: delete snmp - D-Link DES-3326S | Reference Manual - Page 73
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp community Purpose Syntax Description Parameters Used to display SNMP community strings configured on the switch. show snmp community {} The show snmp community command is used to display SNMP community - D-Link DES-3326S | Reference Manual - Page 74
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config snmp engineID Purpose Used to configure a name for the SNMP engine on the switch. Syntax config snmp engineID Description The config snmp engineID command configures a name for the SNMP engine on the switch. - D-Link DES-3326S | Reference Manual - Page 75
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp engineID Purpose Used to display the identification of the SNMP engine on the switch. Syntax show snmp engineID Description The show snmp engineID command displays the identification of the SNMP engine on the switch. - D-Link DES-3326S | Reference Manual - Page 76
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp group Purpose Used to create a new SNMP group, or a table that maps SNMP users to SNMP views. Syntax version 2c will be used. The SNMP v2c supports both centralized and distributed network management strategies. It - D-Link DES-3326S | Reference Manual - Page 77
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp group be used. SNMP v3 provides secure Specifies that there will be no authorization and no encryption of packets sent between the switch and a remote SNMP manager. auth_nopriv − Specifies that authorization will be required, - D-Link DES-3326S | Reference Manual - Page 78
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp group string of up to 32 characters that is used to identify the group of MIB objects that a remote SNMP manager is allowed to access on the switch. notify_view − Specifies that the SNMP group being created can recieve SNMP - D-Link DES-3326S | Reference Manual - Page 79
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete snmp group Purpose Used to remove an SNMP group from the switch. Syntax delete snmp group Description The delete snmp group command is used to remove an SNMP group from the switch. Parameters − - D-Link DES-3326S | Reference Manual - Page 80
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp host Purpose Used to create a recipient of SNMP traps generated by the switch's recipient of SNMP traps generated by the switch's SNMP agent. Parameters − The IP address of the remote management station that will - D-Link DES-3326S | Reference Manual - Page 81
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create snmp host • Message integrity − ensures that packets have not been used to authorize a remote SNMP manager to access the switch's SNMP agent. Only administrator-level users can issue this command. Network Management Commands 81 - D-Link DES-3326S | Reference Manual - Page 82
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To create an SNMP host to receive SNMP messages: DES-3326SR:4#create snmp host 10.48.74.100 v3 auth_priv public Command: create snmp host 10.48.74.100 v3 auth_priv public Success. DES-3326SR:4# 82 Network Management - D-Link DES-3326S | Reference Manual - Page 83
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete snmp host Purpose Used to remove a recipient of SNMP traps generated by the switch's SNMP agent. Syntax delete snmp host Description The delete snmp host command deletes a recipient of SNMP traps generated by the - D-Link DES-3326S | Reference Manual - Page 84
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show snmp host Purpose Used to display the recipient of SNMP traps generated by the switch's SNMP agent. Syntax show snmp host {} Description The show snmp host command is used to display the IP addresses and configuration - D-Link DES-3326S | Reference Manual - Page 85
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable rmon Purpose Syntax Used to enable RMON on the switch. enable rmon Description This command is used, in conjunction with the disable rmon command below, to enable and disable remote monitoring (RMON) on the switch. Parameters - D-Link DES-3326S | Reference Manual - Page 86
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable rmon Purpose Used to disable RMON on the switch. Syntax Description disable rmon This command is used, in conjunction with the enable rmon command above, to enable and disable remote monitoring (RMON) on the switch. - D-Link DES-3326S | Reference Manual - Page 87
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual ping Purpose Syntax default is 0 timeout − defines the time-out period while waiting for a response from the remote device. A value of 1 to 99 seconds can be specified. The default is 1 second. Only administrator-level users - D-Link DES-3326S | Reference Manual - Page 88
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To send ICMP echo message to "10.48.74.121" for 4 times: DES-3326SR:4#ping 10.48.74.121 times 4 Command: ping 10. for 10.48.74.121 Packets: Sent =4, Received =4, Lost =0 DES-3326SR:4# 88 Network Management Commands - D-Link DES-3326S | Reference Manual - Page 89
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual t rac e ro ut command allows you to trace a route between the switch and a give host on the network. − the IP address of the remote device. ttl -level users can issue this command. Example Usage: Network Management - D-Link DES-3326S | Reference Manual - Page 90
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Trace the routed path between the switch and 10.48.74.121. DES-3326SR:4#traceroute 10.48.74.121 probe 3 Command: traceroute 10.48.74.121 probe 3 1 - D-Link DES-3326S | Reference Manual - Page 91
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config mac_notification number, and the highest port number of the range (also separeted by a colon) are specified. The beginning and end of the port list range are seperated by a dash. For example, 1:3 would specify switch number 1, - D-Link DES-3326S | Reference Manual - Page 92
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable mac_notification Purpose Used to enable Mac Address Notification while Mac Address Notification without changing configuration. none. Only administrator-level users can issue this command. Example Usage: To enable or disable MAC - D-Link DES-3326S | Reference Manual - Page 93
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show mac_notification Purpose Syntax Description Parameters To display the current Mac Notification settings of a range of ports. show mac_notification {} This command is used to - D-Link DES-3326S | Reference Manual - Page 94
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 94 Network Management Commands - D-Link DES-3326S | Reference Manual - Page 95
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 7 DOWNLOAD/UPLOAD COMMANDS The download/upload commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command download upload Param e t e rs firmware < - D-Link DES-3326S | Reference Manual - Page 96
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual download Purpose Syntax Description Parameters Used to download and install new firmware or a switch configuration file from a TFTP server. download [ firmware {unit [all/]}/configuration < - D-Link DES-3326S | Reference Manual - Page 97
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual download Restrictions parameters will remain unchanged. The TFTP server must be on the same IP subnet as the switch. Only administratorlevel users can issue this command. Example Usage: DES-3326SR:4#download configuration 10.48.74.121 - D-Link DES-3326S | Reference Manual - Page 98
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual upload Purpose Syntax Description Parameters Restrictions Used to upload the current switch settings or the switch history log to a TFTP server. upload [configuration/log] This command is used to upload - D-Link DES-3326S | Reference Manual - Page 99
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: DES-3326SR:4#upload configuration 10.48.74.121 c:\cfg\log.txt Command: upload configuration 10.48.74.121 c:\cfg\log.txt Connecting to server Done. Upload configuration Done. DES-3326SR:4# Download/Upload Commands 99 - D-Link DES-3326S | Reference Manual - Page 100
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 8 NETWORK MONITORING COMMANDS The network monitoring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command - D-Link DES-3326S | Reference Manual - Page 101
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command Param e t e rs local7 udp_port ipaddress state [enabled/disabled] config syslog host delete syslog host show syslog host all severity informational warning - D-Link DES-3326S | Reference Manual - Page 102
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show packet ports Purpose Syntax Description Parameters Used to display statistics about the packets sent and received by the switch. show packet ports This command is used to display statistics about packets sent and - D-Link DES-3326S | Reference Manual - Page 103
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the packets analysis for port 7 of module 2: DES-3326SR:4#show packet port 2:7 Port number : 2:7 Frame Size Frame Counts Frames/sec Frame Type Total Total/sec 64 3275 10 RX Bytes 408973 1657 65-127 - D-Link DES-3326S | Reference Manual - Page 104
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show error ports Purpose Used to display the error statistics for a range of ports. Syntax show error ports Description This command will display all - D-Link DES-3326S | Reference Manual - Page 105
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the errors of the port 3 of module 1: DES-3326SR:4#show errors port 1:3 RX Frames CRC Error 0 Undersize 0 Oversize 0 Fragment 0 Jabber 0 Drop Pkts 0 TX Frames Excessive Deferral 0 CRC Error - D-Link DES-3326S | Reference Manual - Page 106
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the port utilization statistics: DES-3326SR:4#show utilization Port ---1:1 1:2 1:3 1:4 1:5 1:6 1:7 1:8 1:9 1:10 1:11 1:12 1:13 1:14 1:15 1:16 1:17 1:18 1:19 1:20 1:21 TX/sec ---------- 0 0 0 0 0 0 0 0 0 0 0 0 - D-Link DES-3326S | Reference Manual - Page 107
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual clear counters Purpose Used to clear the switch's statistics counters. Syntax clear counters {ports } Description This command will clear the counters used by the switch to compile statistics. Parameters − - D-Link DES-3326S | Reference Manual - Page 108
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual clear log Purpose Syntax Description Parameters Restrictions Used to clear the switch's history log. clear log This command will clear the switch's history log. none. Only administrator-level users can issue this command. Example Usage: - D-Link DES-3326S | Reference Manual - Page 109
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show log Purpose Syntax Description Parameters Restrictions Used to display the switch history log. show log {index } This command will display the contents of the switch's history log. index − The show log command will - D-Link DES-3326S | Reference Manual - Page 110
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable syslog Purpose Used to enable the system log administrator-level users can issue this command. Example Usage: To the syslog function on the switch: DES-3326SR:4#enable syslog Command: enable syslog Success. DES-3326SR:4# 110 - D-Link DES-3326S | Reference Manual - Page 111
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable syslog Purpose Used to enable the system log -level users can issue this command. Example Usage: To disable the syslog function on the swtich: DES-3326SR:4#disable syslog Command: disable syslog Success. DES-3326SR:4# Network - D-Link DES-3326S | Reference Manual - Page 112
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show syslog Purpose Used to display the syslog protocol status as enabled None. Example Usage: To display the current status of the syslog function: DES-3326SR:4#show syslog Command: show syslog Syslog Global State: Enabled - D-Link DES-3326S | Reference Manual - Page 113
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create syslog host Purpose Used to create a new syslog host. Syntax Bold font indicates that the corresponding severity level is currently supported on the switch. Numerical Code Severity 0 Emergency: system is unusable 1 Alert - D-Link DES-3326S | Reference Manual - Page 114
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create syslog host 6 Informational: informational messages 7 Debug: Bold font means the facility values the switch supports now. Numerical Facility Code 0 kernel messages 1 user-level messages 2 mail system 3 system daemons - D-Link DES-3326S | Reference Manual - Page 115
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create syslog host 8 UUCP subsystem 9 clock daemon 10 security/authorization messages 11 FTP daemon 12 NTP subsystem 13 log audit 14 log alert 15 clock - D-Link DES-3326S | Reference Manual - Page 116
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual send messages to the remote host. ipaddress − Specifies the IP address of the remote host where syslog messages will be sent. Restrictions administrator-level users can issue this command. Example Usage: 116 Network - D-Link DES-3326S | Reference Manual - Page 117
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual To create syslog host: DES-3326SR:4#create syslog host 1 severity all facility local0 Command: create syslog host 1 severity all facility local0 Success. DES-3326SR:4# config syslog host Purpose Used to configure the syslog protocol to - D-Link DES-3326S | Reference Manual - Page 118
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config syslog host corresponding severity level is currently supported on the switch. Numerical Code Severity 0 Emergency: system is unusable 1 Alert: action must be taken immediately 2 Critical: critical conditions 3 Error: error - D-Link DES-3326S | Reference Manual - Page 119
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config syslog host that have been designated are shown in the following: Bold font means the facility values the switch supports now. Numerical Facility Code 0 kernel messages 1 user-level messages 2 mail system 3 system - D-Link DES-3326S | Reference Manual - Page 120
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config syslog host local1 − Specifies that local use 1 messages will be sent to the remote host. This corresponds to number 17 from the list above. - D-Link DES-3326S | Reference Manual - Page 121
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config syslog host number that the syslog protocol will use to send messages to the remote host. ipaddress − Specifies the IP -level users can issue this command. Example Usage: To configure a syslog host: DES-3326SR:4#config - D-Link DES-3326S | Reference Manual - Page 122
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete syslog host Purpose Used to remove a syslog host, that has been previously configured, from the switch -level users can issue this command. Example Usage: To delete a previously configured syslog host: DES-3326SR:4#delete syslog - D-Link DES-3326S | Reference Manual - Page 123
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show syslog host Purpose Used to display the syslog hosts currently configured on the switch : To create DES-3326SR:4#show syslog host Command: show syslog host Syslog Global State: Disabled Host Id Host IP Address Severiry Facility - D-Link DES-3326S | Reference Manual - Page 124
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 9 SPANNING TREE COMMANDS The switch supports 802.1d STP and 802.1w Rapid STP. The spanning tree commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) - D-Link DES-3326S | Reference Manual - Page 125
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config stp Purpose Syntax Description Parameters Used to setup STP and RSTP on the switch (in seconds) that the root device will wait before changing states. The default is 15 seconds. priority − A numerical value between 0 and - D-Link DES-3326S | Reference Manual - Page 126
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config stp Restrictions network devices when STP is disabled on the switch. The default is enabled. Txholdcount - the maximum number of Hello packets transmitted per interval. Default value = 3. version [rstp/stp] - select the - D-Link DES-3326S | Reference Manual - Page 127
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config stp ports Purpose Used to setup STP on and 31 that is used in determining the root and designated port in an STP port list. The default is 16, with 0 indicating the highest priority. − Specifies a range of ports to be - D-Link DES-3326S | Reference Manual - Page 128
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual p2p [true/false] - true indicates a point-topoint (p2p) shared link. These are similar to edge ports however they are restricted in that a default is disabled. Only administrator-level users can issue this command. 128 Spanning Tree - D-Link DES-3326S | Reference Manual - Page 129
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure STP with path cost 19, priority 15, and state enabled for ports 1-5 of module 1. DES-3326SR:4#config stp_ports 1:1-1:5 cost 19 priority 15 state enabled Command: config stp_ports 1-5 cost 19 priority 15 state - D-Link DES-3326S | Reference Manual - Page 130
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To enable STP, globally, on the switch: DES-3326SR:4#enable stp Command: enable stp Success. DES-3326SR:4# 130 Spanning Tree Commands - D-Link DES-3326S | Reference Manual - Page 131
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable stp Purpose Used to globally disable STP on the switch. Syntax disable stp Description This command allows the Spanning Tree Protocol to be globally disabled on the switch. Parameters none. Restrictions Only - D-Link DES-3326S | Reference Manual - Page 132
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show stp Purpose Used to display the switch's current STP configuration. Syntax Description show stp This command displays the switch's current STP configuration. Parameters Restrictions none none. Example Usage: To display the - D-Link DES-3326S | Reference Manual - Page 133
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual DES-3326SR:4#show stp Command: show stp STP Status : Enabled Max Age : Time : 2 Forward Delay : 15 Hold Time : 3 Status 2 : STP Disabled DES-3326SR:4#show stp Command: show stp STP Status : Disabled Max Age : 20 Hello Time : - D-Link DES-3326S | Reference Manual - Page 134
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual DES-3326SR:4# show stp ports Purpose Used to display the switch's current per-port group STP configuration. Syntax show stp ports Description This command displays the switch's current per-port group STP configuration. - D-Link DES-3326S | Reference Manual - Page 135
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show stp ports port 4. 1:3-2:4 specifies all of the ports between switch 1, port 3 and switch 2, port 4 − in numerical order. Restrictions none Example Usage: To display STP state of port 1-9 of module 1: DES-3326SR:4#show stp_ports - D-Link DES-3326S | Reference Manual - Page 136
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 10 FORWARDING DATABASE COMMANDS The layer 2 forwarding > clear fdb vlan port /all show multicast_fdb show fdb vlan mac_address port vlan mac_address < - D-Link DES-3326S | Reference Manual - Page 137
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create fdb Purpose Syntax Description Parameters Used to create a static entry to the unicast MAC address forwarding table (database) create fdb [port ] This command will make an entry into the switch's - D-Link DES-3326S | Reference Manual - Page 138
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create multicast_fdb Purpose Used to create a static entry to the multicast MAC address forwarding table (database) Syntax Description Parameters Restrictions create multicast_fdb This - D-Link DES-3326S | Reference Manual - Page 139
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config multicast_fdb Purpose Used to configure the switch's multicast MAC address forwarding database. Syntax config multicast_fdb [add/delete] Description This command configures the multicast MAC - D-Link DES-3326S | Reference Manual - Page 140
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To add multicast MAC forwarding: DES-3326SR:4#config multicast_fdb default 01-00-5E-00-00-00 add 1:1-1:5 Command: config multicast_fdb default 01-00-5E-00-00-00 add 1:11:5 Success. DES-3326SR:4# 140 Forwarding Database - D-Link DES-3326S | Reference Manual - Page 141
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config macentry unicast aging_time Purpose Used to configure the switch's MAC address aging time. Syntax config macentry unicast aging_time Description Parameters Restrictions This command is used to set the age-out timer for - D-Link DES-3326S | Reference Manual - Page 142
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete fdb Purpose Syntax Description Parameters Restrictions Used to delete an entry to the switch's forwarding database. delete fdb This command is used to delete a previous entry to the switch's MAC address - D-Link DES-3326S | Reference Manual - Page 143
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual clear fdb Purpose Syntax Description Used to clear the switch's forwarding database of all dynamically learned MAC addresses. clear fdb [vlan /port /all] Clears dynamically learned entries to the switch's forwarding - D-Link DES-3326S | Reference Manual - Page 144
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show multicast_fdb Purpose Used to display the contents of the switch's multicast forwarding database. Syntax show mulitcast_fdb [vlan /mac_address Description This command is used to display the current - D-Link DES-3326S | Reference Manual - Page 145
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show fdb Purpose Syntax Description Parameters Restrictions Used to display the current unicast MAC address forwarding database. show fdb {port /vlan /m ac _addre ss /st at i c /agi ng_t i m e } This - D-Link DES-3326S | Reference Manual - Page 146
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display unicast MAC address table: DES-3326SR:4#show fdb Command: show fdb Unicast MAC Address Ageing Time = 300 VID VLAN Name 1 default 1 default 1 default MAC Address Port Type 00-00-00-00-01-01 ALL - D-Link DES-3326S | Reference Manual - Page 147
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 11 BROADCAST STORM CONTROL COMMANDS The broadcast storm control commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the - D-Link DES-3326S | Reference Manual - Page 148
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config traffic Specifies all broadcast storm control groups on the switch. broadcast [enabled/disabled] − Enables or disables threshold at which the specified traffic control is switched on. The is the number of broadcast/multicast/dlf - D-Link DES-3326S | Reference Manual - Page 149
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure traffic control: DES-3326SR:4#config traffic control 1-3,1-2 broadcast enabled Command: config traffic control 1-1,2-2 broadcast enabled Success. DES-3326SR:4# show traffic control Purpose Used to display - D-Link DES-3326S | Reference Manual - Page 150
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display traffic control setting: DES-3326SR:4#show traffic control Command: show traffic control Traffic Control Broadcast Multicast Destination Group [ports] Threshold Storm Storm Lookup Fail 1 [ 1 - 8 ] 128 Enabled - D-Link DES-3326S | Reference Manual - Page 151
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 12 QOS COMMANDS The MAC address priority commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 152
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config bandwidth_control Purpose Used to configure bandwidth control on a by-port basis. Syntax config bandwidth_control {re_rate [no_limit/]/tx_rate [no_limit/]} Description - D-Link DES-3326S | Reference Manual - Page 153
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config bandwidth_control − Specifies the limit, 8>. Restrictions Only administrator-level users can issue this command. Example Usage: To configure bandwidth control: DES-3326SR:4#config bandwidth_control 1-10 tx_rate 10 - D-Link DES-3326S | Reference Manual - Page 154
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show bandwidth_control Purpose Used to display the bandwidth control configuration on the switch. Syntax show bandwidth_control {} Description The show bandwidth_control command displays the current bandwidth control - D-Link DES-3326S | Reference Manual - Page 155
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To create DES-3326SR:4#show bandwidth_control 1-10 Command: show bandwidth_control 1-10 Bandwidth Control Table Port RX Rate (Mbit/sec) TX_RATE (Mbit/sec) 1 no_limit 10 2 no_limit 10 3 no_limit 10 4 no_limit - D-Link DES-3326S | Reference Manual - Page 156
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config scheduling Purpose Used to configure traffic scheduling for each of the switch's COS queues. Syntax config scheduling {max_packet /max_latency } Description The switch switch's default - D-Link DES-3326S | Reference Manual - Page 157
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config scheduling specify the maximum amount of time that packets will be delayed before being transmitted. For a given priority queue, a value between 0 and 255 can - D-Link DES-3326S | Reference Manual - Page 158
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config scheduling before being allowed to transmit any have to wait. Restrictions Only administrator-level users can issue this command. Example Usage: To create DES-3326SR:4# config scheduling 0 max_packet 100 max_latency 150 - D-Link DES-3326S | Reference Manual - Page 159
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show scheduling switch. The switch's default max_latency = 0. At this value it will empty the four hardware queues in order, from the highest priority (queue 0) to the lowest priority (queue 3). Parameters None. - D-Link DES-3326S | Reference Manual - Page 160
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config 802.1p user_priority Purpose Used to map the 802.1p user priority of an incoming packet to one of the four hadware queues available on the switch. Syntax config 802.1p user_priority Description - D-Link DES-3326S | Reference Manual - Page 161
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config 802.1p user_priority Restrictions − Specifies which of the switch's hardware priority queues the 802.1p priority value (specified above) will be mapped to. Only administrator-level users can issue this command. - D-Link DES-3326S | Reference Manual - Page 162
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show 802.1p user_priority Purpose Used to display the current mapping between an incoming packet's 802.1p priority value and one of the switch's four hardware priority queues. Syntax show 802.1p user_priority Description The show - D-Link DES-3326S | Reference Manual - Page 163
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config 802.1p default_priority Purpose Used to specify how to map an incoming packet that has no 802.1p priority tag to one of the switch's four hardware priority queues. Syntax config 802.1p default_priority [/all] < - D-Link DES-3326S | Reference Manual - Page 164
3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config 802.1p default_priority packet will be given before being forwarded to its destination. Restrictions Only administrator-level users can issue this command. Example Usage: To configure 802.1p default priority on the switch: DES-3326SR - D-Link DES-3326S | Reference Manual - Page 165
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show 802.1 default_priority Purpose Used to display the currently configured 802.1p priority value that will be assigned to an incoming, untagged packet before being - D-Link DES-3326S | Reference Manual - Page 166
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the current 802.1p default priority configuration on the switch: DES-3326SR:4# show 802.1p default_priority Command: show 802.1p default_priority Port ------- 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 - D-Link DES-3326S | Reference Manual - Page 167
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 15 PORT MIRRORING COMMANDS The port mirroring commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 168
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config mirror port Purpose Used to configure a mirror port − source port pair on the switch. Syntax config mirror port add source ports [rx/tx/both] Description This command allows a range of ports to have all of - D-Link DES-3326S | Reference Manual - Page 169
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config mirror port tx − Allows the mirroring of or ports in the port list. Only administrator-level users can issue this command. Example Usage: To add the mirroring ports: DES-3326SR:4#config mirror port 1:5 add source ports 1-5 both - D-Link DES-3326S | Reference Manual - Page 170
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config mirror delete Purpose Used to delete a port mirroring configuration/ Syntax config mirror < the port or ports in the port list. Restrictions Only administrator-level users can issue this command. 170 Port Mirroring Commands - D-Link DES-3326S | Reference Manual - Page 171
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To delete the mirroring ports: DES-3326SR:4#config mirror 1:5 delete source 1-5 both Command: config mirror 1:5 delete source 1-5 both Success. DES-3326SR:4# enable mirror Purpose Used to enable a previously entered port - D-Link DES-3326S | Reference Manual - Page 172
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable mirror Purpose Used to disable a previously entered port level users can issue this command. Example Usage: To disable mirroring configurations: DES-3326SR:4#disable mirror Command: disable mirror Success. DES-3326SR:4# - D-Link DES-3326S | Reference Manual - Page 173
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show mirror Purpose Used to show the current port mirroring configuration on the switch. Syntax show mirror Description This command displays the current port mirroring configuration on the switch. Parameters none Restrictions - D-Link DES-3326S | Reference Manual - Page 174
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 14 VLAN COMMANDS The VLAN commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create vlan delete vlan config vlan config vlan config vlan show vlan - D-Link DES-3326S | Reference Manual - Page 175
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create vlan Purpose Syntax Description Parameters Used to create a VLAN on the switch. create vlan {tag /adv e rt i se m e nt } This command allows you to create a VLAN on the switch. − The name of the - D-Link DES-3326S | Reference Manual - Page 176
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete vlan Purpose Used to delete a previously configured VLAN on the switch. Syntax delete vlan Description This command will delete a previously configured VLAN on the switch. Parameters − The VLAN name - D-Link DES-3326S | Reference Manual - Page 177
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config vlan Purpose Used to add additional ports to a previously configured VLAN. Syntax config vlan add [t agge d/unt agge d/f o rbi dde n]/de le t e /adv e rt i se m e nt [enabled/disabled]} Description - D-Link DES-3326S | Reference Manual - Page 178
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config vlan highest port number of the range (also separated by a colon) are specified. The beginning and end of the port list range are separated by a dash. For example, 1:3 would specify switch number 1, port 3. 2:4 specifies switch - D-Link DES-3326S | Reference Manual - Page 179
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config gvrp Purpose Syntax Description Parameters Used to configure GVRP on the switch. config gvrp [/all] {state [enabled/disabled]/ingress_checking [enabled/disabled]} This command is used to configure the Group VLAN - D-Link DES-3326S | Reference Manual - Page 180
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To set the ingress checking status, the sending and receiving GVRP information and Port VLAN ID(PVID): DES-3326SR:4#config gvrp 1:1-1:5 state enabled ingress_checking enabled pvid 21 Command: config gvrp 1:1-1:5 state - D-Link DES-3326S | Reference Manual - Page 181
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable gvrp Purpose Used to enable GVRP on the switch. Syntax enable gvrp Description This command, along with disable gvrp below, is used to enable and disable GVRP on the switch − without changing the GVRP configuration on the - D-Link DES-3326S | Reference Manual - Page 182
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable gvrp Purpose Used to disable GVRP on the switch. Syntax disable gvrp Description This command, along with disable gvrp below, is used to enable and disable GVRP on the switch − without changing the GVRP configuration on the - D-Link DES-3326S | Reference Manual - Page 183
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show vlan Purpose Syntax Description Used to display the current VLAN configuration on the switch show vlan {} This command displays summary information about each VLAN including the VLAN ID, VLAN name, the Tagging/Untagging - D-Link DES-3326S | Reference Manual - Page 184
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Static ports : 1:26,2:26 Untagged ports : Forbidden ports : Total Entries : 2 DES-3326SR:4# show gvrp Purpose Syntax Description Parameters Used to display the GVRP status for a port list on the switch. show gvrp {} This - D-Link DES-3326S | Reference Manual - Page 185
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show gvrp Restrictions None. Example Usage: To display GVRP port status: DES-3326SR:4#show gvrp Command: show gvrp Global GVRP : Disabled Port Disabled Disabled Disabled Disabled Disabled Disabled Disabled Disabled VLAN Commands 185 - D-Link DES-3326S | Reference Manual - Page 186
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 1:22 1 1:23 1 1:24 1 1:25 1 1:26 0 2:1 1 2:2 1 2:3 1 2:4 1 2:5 1 2:6 1 2:7 1 2:8 1 2:9 1 2:10 1 2:11 1 2:12 1 2:13 1 2:14 1 2:15 1 2:16 1 2:17 1 2:18 1 2:19 1 2:20 1 2:21 1 2:22 1 2:23 1 2:24 1 2:25 1 2:26 0 Disabled Disabled Disabled - D-Link DES-3326S | Reference Manual - Page 187
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 17 LINK AGGREGATION COMMANDS The link aggregation commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create link_aggregation group_id - D-Link DES-3326S | Reference Manual - Page 188
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create link_aggregation group_id Purpose Used to create a link aggregation group on the switch. Syntax create link_aggregation group_id Description This command will create a link aggregation group. Parameters − - D-Link DES-3326S | Reference Manual - Page 189
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete link_aggregation group_id Purpose Used to delete a previously configured link aggregation group. Syntax delete link_aggregation group_id Description This command is used to delete a previously configured link - D-Link DES-3326S | Reference Manual - Page 190
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config link_aggregation Purpose Used to configure a previously created link aggregation group. Syntax config link_aggregation group_id {master_port /ports / {state [enabled/disabled]} Description This command - D-Link DES-3326S | Reference Manual - Page 191
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config link_aggregation port number, separated by commas. state [enabled/disabled] − Allows you to enable or disable the specified link aggregation group. Restrictions Only administrator-level users can issue this command. Example - D-Link DES-3326S | Reference Manual - Page 192
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config link_aggregation algorithm Purpose Used to configure the link aggregation algorithm. Syntax config link_aggregation algorithm [m ac _so urc e /m ac _de st i nat i o n/m ac _so urc e _de st/ ip_source/ip_destination/ - D-Link DES-3326S | Reference Manual - Page 193
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure link aggregation algorithm for mac-source-dest: DES-3326SR:4#config link_aggregation algorithm mac_source_dest Command: config link_aggregation algorithm mac_source_dest Success. DES-3326SR:4# Link Aggregation - D-Link DES-3326S | Reference Manual - Page 194
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show link_aggregation Purpose Syntax Description Parameters Restrictions Used to display the current link aggregation configuration on the switch. show link_aggregation {group_id /algo ri t hm } This command will display the - D-Link DES-3326S | Reference Manual - Page 195
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 18 IP INTERFACE COMMANDS The IP interface commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Param e t e rs create ipif vlan < - D-Link DES-3326S | Reference Manual - Page 196
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ipif Purpose Syntax Description Parameters Restrictions Used to create an IP interface on the switch. create ipif {state [enabled/disabled]} This command will create an IP interface. < - D-Link DES-3326S | Reference Manual - Page 197
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To create IP address 20.1.1.1 of IP interface ip2: DES-3326SR:4#create ipif ip2 20.1.1.1/8 vlan2 state enabled Command: create ipif ip2 20.1.1.1/8 vlan2 state enabled Success. DES-3326SR:4# IP Interface Commands 197 - D-Link DES-3326S | Reference Manual - Page 198
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ipif Purpose Syntax Description Parameters Restrictions Used to configure an IP interface on the switch. config ipif {vlan enable or disable the IP interface. Only administrator-level users can issue this command. 198 - D-Link DES-3326S | Reference Manual - Page 199
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure the IP interface ip2: DES3326S:4#config ipif ip2 vlan vlan1 Command: config ipif ip2 vlan vlan1 Success. DES-3326SR:4# IP Interface Commands 199 - D-Link DES-3326S | Reference Manual - Page 200
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete ipif Purpose Syntax Description Parameters Restrictions Used to delete a previously configured IP interface on the switch. delete ipif {/all} This command will delete an IP interface from the switch. − The - D-Link DES-3326S | Reference Manual - Page 201
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ipif System Purpose Used to configure the System IP interface. Syntax config ipif System [{vlan /i paddre ss /st at e [e nable d/di sable d]/bo o t p/dhc p} ] Description This command is - D-Link DES-3326S | Reference Manual - Page 202
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure the IP interface System: DES-3326SR:4#config ipif System ipaddress 10.48.74.122/8 Command: config ipif System ipaddress 10.48.74.122/8 Success. DES-3326SR:4# 202 IP Interface Commands - D-Link DES-3326S | Reference Manual - Page 203
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ipif Purpose Syntax Description Parameters Restrictions Used to configure an IP interface on the switch. config ipif {vlan IP interface. Only administrator-level users can issue this command. IP Interface Commands 203 - D-Link DES-3326S | Reference Manual - Page 204
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure the IP interface ip2: DES-3326SR:4#config ipif ip2 vlan vlan1 Command: config ipif ip2 vlan vlan1 Success. DES-3326SR:4# 204 IP Interface Commands - D-Link DES-3326S | Reference Manual - Page 205
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable ipif Purpose Syntax Description Parameters Restrictions Used to enable an IP interface on the switch. enable ipif {/all} This command, along with the disable ipif command below, allows you to enable or disable an IP - D-Link DES-3326S | Reference Manual - Page 206
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable ipif Purpose Used to disable an IP interface on the switch. Syntax disable ipif {/all} Description This command, along with the enable ipif command above, allows you to enable or disable an IP interface on the - D-Link DES-3326S | Reference Manual - Page 207
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ipif Purpose Syntax Description Parameters Restrictions Used to display the configuration of an IP interface on the switch. show ipif {} This command will display the configuration of an IP interface on the switch. < - D-Link DES-3326S | Reference Manual - Page 208
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 19 ARP COMMANDS The ARP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command create - D-Link DES-3326S | Reference Manual - Page 209
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create arpentry Purpose Used to make a static entry into the ARP table. Syntax create arpentry Description This command is used to enter an IP address and the corresponding MAC address into the switch's ARP table. - D-Link DES-3326S | Reference Manual - Page 210
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete arpentry Purpose users can issue this command. Example Usage: To delete an entry of IP address 10.48.74.121 from the ARP table: DES-3326SR:4#delete arpentry 10.48.74.121 Command: delete arpentry 10.48.74.121 Success. DES-3326SR - D-Link DES-3326S | Reference Manual - Page 211
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config arp_aging Purpose Used to configure the age-out timer for ARP table entries on the switch. Syntax config arp_aging time Description This command sets the maximum amount of time, in seconds, that an ARP entry can - D-Link DES-3326S | Reference Manual - Page 212
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show arpentry Purpose Used to display the ARP table. Syntax show arpentry {ipif /ipaddress /static} Description This command is used to display the current contents of the switch's ARP table. Parameters - D-Link DES-3326S | Reference Manual - Page 213
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual System System System System System System System System System System System System System System System System System System -00 Local 10.255.255.255 FF-FF-FF-FF-FF-FF Local/Broadcast Total Entries = 20 DES-3326SR:4# Arp Commands 213 - D-Link DES-3326S | Reference Manual - Page 214
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual clear arptable Purpose Used to remove all dynamic ARP table entries. Syntax clear arptable Description This command is used to remove dynamic ARP table entries from the switch's ARP table. Static ARP table entries are not affected. - D-Link DES-3326S | Reference Manual - Page 215
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 20 ROUTING TABLE COMMANDS The routing table commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command create iproute delete iproute show iproute Param e t e rs default - D-Link DES-3326S | Reference Manual - Page 216
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create iproute Purpose Used to create an IP route entry to the switch's IP routing table. Syntax create iproute [default/] { } Description This command is used to create an IP route entry to - D-Link DES-3326S | Reference Manual - Page 217
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To add a static address 10.48.74.121 , mask 255.0.0.0 and gateway 10.1.1.254 to the routing table: DES-3326SR:4#create iproute 10.48.74.121/255.0.0.0 10.1.1.254 1 Command: create iproute 10.48.74.121/8 10.1.1.254 1 Success. - D-Link DES-3326S | Reference Manual - Page 218
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To delete a static address 10.48.75.121, mask 255.0.0.0 from the routing table: DES-3326SR:4#delete iproute 10.48.74.121/255.0.0.0 Command: delete iproute 10.48.74.121/8 Success. DES-3326SR:4# show iproute Purpose Used to - D-Link DES-3326S | Reference Manual - Page 219
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display the contents of the IP routing table: DES-3326SR:4#show iproute Command: show iproute IP Address Protocol 0.0.0.0 Default 10.0.0.0 Local Netmask Gateway Interface Name Hops ---- ------ 0.0.0.0 0.1.1. - D-Link DES-3326S | Reference Manual - Page 220
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 21 ROUTE REDISTRIBUTION COMMANDS The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command Parameters create route redistribute dst - D-Link DES-3326S | Reference Manual - Page 221
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create route redistribute dst ospf Purpose Used to add route redistribution settings for the exchange of RIP routes to OSPF routes on the switch. Syntax create route redistribute dst ospf src [static/rip/local] {mettype [1/2]/metric - D-Link DES-3326S | Reference Manual - Page 222
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create route redistribute dst ospf Restrictions Only administrator-level users can issue this command. Routing information source − RIP. the Static Route table, and the Local interface routing information. Routing information will be - D-Link DES-3326S | Reference Manual - Page 223
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To add route redistribution settings: DES-3326SR:4#create route redistribute dst ospf src rip Command: create route redistribute dst ospf src rip Success. DES-3326SR:4# create route redistribute dst rip Purpose Used to - D-Link DES-3326S | Reference Manual - Page 224
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create route redistribute dst rip the destination device. metric − Allows the entry of an OSPF interface cost. this is analogous to a HOP Count in the RIP routing protocol. Restrictions Only administrator-level users can issue - D-Link DES-3326S | Reference Manual - Page 225
3 Fast Ethernet Switch CLI Reference Manual Entering the metric 0 specifies transparency. Example Usage: To add route redistribution settings: DES-3326SR:4#create route redistribute dst rip src ospf all metric 2 Command: create route redistribute dst rip src ospf all metric 2 Success. DES-3326SR - D-Link DES-3326S | Reference Manual - Page 226
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To delete route redistribution settings: DES-3326SR:4#delete route redistribute dst rip src ospf Command: delete route redistribute dst rip src ospf Success. DES-3326SR:4# config route redistribute dst ospf Purpose Used - D-Link DES-3326S | Reference Manual - Page 227
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config route redistribute dst ospf redistributed. Parameters to a Hop Count in the RIP routing protocol. Restrictions Only administrator-level users can issue this command. Routing information source − RIP: the Static Route table - D-Link DES-3326S | Reference Manual - Page 228
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Route Source RIP Metric 0 to 16777214 Static 0 to 16777214 in OSPF as the metric 20. Example Usage: To configure route redistributions: DES-3326SR:4#config route redistribute dst rip src ospf all metric 2 Command: config route - D-Link DES-3326S | Reference Manual - Page 229
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config route redistribute dst rip Purpose Syntax Description Parameters Restrictions Used is analogous to a Hop Count in the RIP routing protocol. Only administrator-level users can issue this command. Route Redistribution Commands 229 - D-Link DES-3326S | Reference Manual - Page 230
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Routing information source − OSPF and the Static Route table the metric 0 specifies transparency. Example Usage: To configure route redistributions: DES-3326SR:4#config route redistribute dst ospf src rip mettype type_1 metric 2 Command: - D-Link DES-3326S | Reference Manual - Page 231
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual DES-3326SR:4# show route redistribute Purpose Used to display the route redistribution on the switch. Syntax show route redistribute {dst [rip/ospf]/src [ri p/st at i c /lo c al/o spf ]} Description Displays the current route - D-Link DES-3326S | Reference Manual - Page 232
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual STATIC RIP LOCAL OSPF Total Entries : 2 DES-3326SR:4# -------All Type-2 -------1 20 232 Route Redistribution Commands - D-Link DES-3326S | Reference Manual - Page 233
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 22 IGMP COMMANDS The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config igmp show igmp show - D-Link DES-3326S | Reference Manual - Page 234
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp Purpose Used to configure IGMP on the switch. Syntax Description Parameters switch. − The name of the IP interface for which you want to configure IGMP. all − Specifies all the IP interfaces on the switch. - D-Link DES-3326S | Reference Manual - Page 235
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp Restrictions Only administrator-level users can issue this command. Example Usage: To configure the IGMP for the IP interface System. DES-3326SR:4#config igmp all version 1 state enabled Command: config igmp all version 1 - D-Link DES-3326S | Reference Manual - Page 236
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display IGMP configurations: DES-3326SR:4#show igmp Command: show igmp Interface IP Address Ver- Query Maximum Robust- Last Member State sion Response ness Query Time Value Interval ------ - System 10.90.90 - D-Link DES-3326S | Reference Manual - Page 237
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show igmp group Purpose Used to display the switch's IGMP group table. group table: DES-3326SR:4#show igmp group Command: show igmp group Interface Name Multicast Group Last Reporter Querier IP Address IP Expire Time System - D-Link DES-3326S | Reference Manual - Page 238
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 259 Total Entries: 5 DES-3326SR:4# 238 IGMP Commands - D-Link DES-3326S | Reference Manual - Page 239
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 23 IGMP SNOOPING COMMANDS The switch port commands in the Command Line Interface (CLI) are vlan_name> [add/delete] forward_mcrouter_only vlan vlan vlan static IGMP Snooping Commands 239 - D-Link DES-3326S | Reference Manual - Page 240
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command Param e t e rs dynamic Each command is listed, in detail, in the following sections. 240 IGMP Snooping Commands - D-Link DES-3326S | Reference Manual - Page 241
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp_snooping Purpose Used to configure IGMP snooping on the switch. Syntax config igmp_snooping [/all] {host_timeout /router_timeout /leave_timer /state [enabled/disabled]} Description This command - D-Link DES-3326S | Reference Manual - Page 242
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp_snooping Restrictions Only administrator-level users can issue this command. Example Usage: To configure the igmp snooping: DES-3326SR:4#config igmp_snooping default host_timeout 250 state enabled Command: config - D-Link DES-3326S | Reference Manual - Page 243
-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp_snooping querier Parameters − The name of the VLAN for which IGMP snooping querier is to be configured. query_interval − Specifies the amount of time in seconds between general query transmissions. the default - D-Link DES-3326S | Reference Manual - Page 244
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config igmp_snooping querier Restrictions • Last member query count- Number of group-specific queries sent before the router assumes there are no local members of a group. The default number is the value of the robustness variable. • By - D-Link DES-3326S | Reference Manual - Page 245
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To configure the igmp snooping: DES-3326SR:4#config igmp_snooping querier default query_interval 125 state enabled Command: config igmp_snooping querier default query_interval 125 state enabled Success. DES-3326SR the VLAN on - D-Link DES-3326S | Reference Manual - Page 246
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config router_ports the highest port number in a group, separated by a dash. So, a port group including the switch ports 1, 2, and 3 would be entered as 1-3. Ports that are not contained within a group are specified by entering their port - D-Link DES-3326S | Reference Manual - Page 247
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable igmp_snooping Purpose Used to enable IGMP snooping on the switch. Syntax enable igmp_snooping {f o rward_m c ro ut e r_o nly } Description This command allows you to enable IGMP snooping on the switch. If - D-Link DES-3326S | Reference Manual - Page 248
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable igmp_snooping Purpose Used to enable IGMP snooping on the switch. Syntax disable igmp_snooping Description This command disables IGMP snooping on the switch. IGMP snooping can be disabled only if IP multicast routing is not - D-Link DES-3326S | Reference Manual - Page 249
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show igmp_snooping Purpose Used to show the current status of IGMP snooping on the switch. Syntax show igmp_snooping {vlan } Description This command will display the current IGMP snooping configuration on the switch. - D-Link DES-3326S | Reference Manual - Page 250
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual State VLAN Name Query Interval Max Response Time Robustness Value Last Member Query Interval Host Timeout Route Timeout Leave Timer Querier State Querier Router Behavior State : Disabled : - D-Link DES-3326S | Reference Manual - Page 251
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show igmp_snooping group Purpose Used to display the current IGMP snooping group configuration on the switch. Syntax show igmp_snooping group {vlan } Description This command will display the current IGMP snooping - D-Link DES-3326S | Reference Manual - Page 252
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual VLAN Name Multicast group MAC address Reports Port Member VLAN Name Multicast group MAC address Reports Port Member VLAN Name Multicast group MAC address Reports Port Member VLAN Name Multicast group MAC address Reports Port Member Total - D-Link DES-3326S | Reference Manual - Page 253
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show router_ports Purpose Used to display the currently configured router ports on the switch. Syntax show router_ports {vlan } { st at i c /dy nam i c } Description This command will display the router ports currently - D-Link DES-3326S | Reference Manual - Page 254
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Total Entries: 2 DES-3326SR:4# 254 IGMP Snooping Commands - D-Link DES-3326S | Reference Manual - Page 255
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 24 BOOTP RELAY COMMANDS The BOOTP relay commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 256
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config bootp_relay Purpose Used to configure the BOOTP relay feature of the switch. Syntax config bootp_relay {hops } {time } Description This command is used to configure the BOOTP relay feature. Parameters hops < - D-Link DES-3326S | Reference Manual - Page 257
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config bootp_relay add Purpose Used to add an IP destination address to the switch's BOOTP relay table. Syntax config bootp_relay add ipif Description This command adds an IP address as a destination to forward - D-Link DES-3326S | Reference Manual - Page 258
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config bootp_relay delete Purpose Used to delete one or all IP destination addresses from the switch's BOOTP relay table. Syntax config bootp_relay delete ipif Description This command is used to delete one or - D-Link DES-3326S | Reference Manual - Page 259
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable bootp_relay Purpose Used to enable the BOOTP relay function on the switch. Syntax enable bootp_relay Description This command, in combination with the disable bootp_relay command below, is used to enable and disable the BOOTP - D-Link DES-3326S | Reference Manual - Page 260
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable bootp_relay Purpose Used to disable the BOOTP relay function on the switch. Syntax disable bootp_relay Description This command, in combination with the enable bootp_relay command above, is used to enable and disable the - D-Link DES-3326S | Reference Manual - Page 261
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show bootp_relay Purpose Used to display the current BOOTP relay configuration. Syntax show bootp_relay {ipif } Description This command will display the current BOOTP relay configuration for the switch, or if an IP - D-Link DES-3326S | Reference Manual - Page 262
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 25 DNS RELAY COMMANDS The DNS relay commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 263
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config dnsr Purpose Used to configure the DNS relay function. Syntax config dnsr [primary/secondary] nameserver Description This command is used to configure the DNS relay function on the switch. Parameters primary − - D-Link DES-3326S | Reference Manual - Page 264
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config dnsr [add/delete] static Purpose Used to add or delete a static entry into the switch's DNS resolution table. Syntax config dnsr [add/delete] static Description This command allows you to add or delete - D-Link DES-3326S | Reference Manual - Page 265
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual To delete an entry domain name dns1, IPaddress 10.43.21.12 from DNS static table. DES-3326SR:4#config dnsr delete static dns1 10.43.21.12 Command: config dnsr delete static dns1 10.43.21.12 Success. DES-3326SR:4# enable dnsr Purpose - D-Link DES-3326S | Reference Manual - Page 266
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable dnsr Purpose Used to disable DNS relay on the switch. Syntax disable dnsr Description This command is used, in combination with the enable dnsr command above, to enable and disable DNS Relay on the switch. Parameters none. - D-Link DES-3326S | Reference Manual - Page 267
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable dnsr cache Purpose Used to enable the Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To enable cache lookup for DNS relay. DES-3326SR:4#enable dnsr cache Command: enable - D-Link DES-3326S | Reference Manual - Page 268
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable dnsr cache Purpose Used to disable Parameters none. Restrictions Only administrator-level users can issue this command. Example Usage: To disable cache lookup for DNS relay. DES-3326SR:4#disable dnsr cache Command: disable - D-Link DES-3326S | Reference Manual - Page 269
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable dnsr static Purpose Used to enable the DNS none. Restrictions Only administrator-level users can issue this command. Example Usage: To enable static table lookup for DNS relay: DES-3326SR:4#enable dnsr static Command: enable - D-Link DES-3326S | Reference Manual - Page 270
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable dnsr static Purpose Used to disable the none. Restrictions Only administrator-level users can issue this command. Example Usage: To disable static table lookup for DNS relay. DES-3326SR:4#disable dnsr static Command: disable - D-Link DES-3326S | Reference Manual - Page 271
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show dnsr Purpose Syntax Description Parameters none. Example Usage: To display DNS relay table: DES-3326SR:4#show dnsr static Command: show dnsr static DNS Relay Static Table Domain Name IP Address www.123.com.tw 10.12.12.123 - D-Link DES-3326S | Reference Manual - Page 272
Fast Ethernet Switch CLI Reference Manual DES-3326SR:4#show dnsr Command: show dnsr DNSR Status : Disabled Primary Name Server : 10.48.74.122 Secondary Name Server : 20.48.74.123 DNSR Cache Status : Enabled DNSR Static Table Status : Enabled DNS Relay Static Table Domain Name IP Address - D-Link DES-3326S | Reference Manual - Page 273
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 26 RIP COMMANDS The RIP commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config - D-Link DES-3326S | Reference Manual - Page 274
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config rip rx_mode Purpose Used to configure RIP on the switch. Syntax Description Parameters config rip [ipif /all] rx_mode [[di sable /v 1 _o nly ]/[v 2 _o nly /v 1 _and_v 2 ] authentication [enabled/disabled] ] - D-Link DES-3326S | Reference Manual - Page 275
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config rip rx_mode Restrictions Only administrator-level users can issue this command. Example Usage: To change the RIP receive mode for the IP interface System. DES-3326SR:4#config rip ipif System rx_mode v1_only Command: config rip - D-Link DES-3326S | Reference Manual - Page 276
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config rip tx_mode Purpose switch. − Allows the specification of a case-sensitive password. If no IP interface is specified, the setting is applied to all IP interfaces. The default is disabled. Only administrator-level users - D-Link DES-3326S | Reference Manual - Page 277
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To change the RIP transmission mode for the IP interface System. DES-3326SR:4#config rip ipif System tx_mode v1_only Command: config rip ipif System tx_mode v1_only Success. DES-3326SR:4# RIP Commands 277 - D-Link DES-3326S | Reference Manual - Page 278
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable rip Purpose Syntax Description Parameters Restrictions Used to enable RIP. enable rip This command is used, along with the disable RIP command below, to enable or disable RIP on the switch. none. Only administrator-level users can - D-Link DES-3326S | Reference Manual - Page 279
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable rip Purpose Syntax Description Parameters Restrictions Used to disable RIP. disable rip This command is used, along with the enable RIP command below, to enable or disable RIP on the switch. none. Only administrator-level users - D-Link DES-3326S | Reference Manual - Page 280
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show rip Purpose Syntax Description Parameters Restrictions Used to display the RIP configuration and statistics for the switch. show rip {ipif } This command will display the RIP configuration and statistics for a given IP - D-Link DES-3326S | Reference Manual - Page 281
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 27 DVMRP COMMANDS The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command config dvmrp enable dvmrp disable - D-Link DES-3326S | Reference Manual - Page 282
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config dvmrp Purpose Used to configure DVMRP on the switch switch. − The name of the IP interface default value is 35 seconds. state [enabled/disabled] − Allows DVMRP to be enabled or disabled. Only administrator-level users - D-Link DES-3326S | Reference Manual - Page 283
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config dvmrp this command. Example Usage: To configure DVMRP configurations of IP interface System: DES-3326SR:4#config dvmrp ipif System neighbor_timeout 30 metric 1 probe 5 Command: config dvmrp ipif System neighbor_timeout 30 metric 1 - D-Link DES-3326S | Reference Manual - Page 284
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable dvmrp Purpose Used to enable DVMRP. Syntax enable dvmrp Description This command, in combination with the disable dvmrp below, to enable and disable DVMRP on the switch. Parameters none. Restrictions Only administrator- - D-Link DES-3326S | Reference Manual - Page 285
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable dvmrp Purpose Used to disable DVMRP. Syntax disable dvmrp Description This command, in combination with the enable dvmrp above, to enable and disable DVMRP on the switch. Parameters none. Restrictions Only administrator- - D-Link DES-3326S | Reference Manual - Page 286
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show dvmrp routing_table Purpose Used to display the routing table. ipaddress − The IP address and netmask of the destination. You can specify the IP address and netmask information using the traditional format - D-Link DES-3326S | Reference Manual - Page 287
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display DVMRP routing table: DES-3326SR:4#show dvmrp routing_table Command: show dvmrp routing_table DVMRP Routing Table Source Address Source Mask Next Hop Router Hop Learned Interface Expire 10.0.0.0 255 - D-Link DES-3326S | Reference Manual - Page 288
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show dvmrp neighbor Purpose IP address and netmask information using the traditional format or the CIDR format. For example, 10.1.2.3/255.255.0.0 or 10.2.3.4/16. none. Example Usage: To display DVMRP neighbor table: DES-3326SR - D-Link DES-3326S | Reference Manual - Page 289
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show dvmrp nexthop Purpose Used to display the next hop table. ipaddress − The IP address and netmask of the destination. You can specify the IP address and netmask information using the traditional format or - D-Link DES-3326S | Reference Manual - Page 290
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Example Usage: To display DVMRP routing next hop table: DES-3326SR:4#show dvmrp nexthop Command: show dvmrp nexthop Source IP Address 10.0.0.0 10.0.0.0 20.0.0.0 20.0.0.0 30.0.0.0 30.0.0.0 Source Mask 255.0.0.0 255.0.0.0 255.0.0.0 - D-Link DES-3326S | Reference Manual - Page 291
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show dvmrp Purpose Used to display the current DVMRP routing table. Syntax show dvmrp {} Description The command will display the current DVMRP routing table. Parameters − The name of the IP interface for - D-Link DES-3326S | Reference Manual - Page 292
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 28 IP MULTICASTING COMMANDS The IP multicasting commands in the Command Line Interface (CLI) are listed (along protocol [dvmrp/pim]} Each command is listed, in detail, in the following sections. 292 IP Multicasting Commands - D-Link DES-3326S | Reference Manual - Page 293
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ipmc cache Purpose Used to display the current IP multicast forwarding cache. Syntax show ipmc cache {group } {ipaddres } Description This command will display the current IP multicast forwarding - D-Link DES-3326S | Reference Manual - Page 294
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Usage Example: To display the current IP multicast forwarding cache: DES-3326SR:4#show ipmc cache Command: show ipmc cache Multicast Group Source IP Addr. Source Mask Upstream Expire Prot. Neighbor Time 224.1.1.1 - D-Link DES-3326S | Reference Manual - Page 295
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ipmc Purpose Syntax Description Parameters Restrictions Used to display the IP multicast interface table. show ipmc {ipif /protocol [dv m rp/pi m ]} This command will display the current IP multicast interface table. < - D-Link DES-3326S | Reference Manual - Page 296
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 29 MD5 CONFIGURATION COMMANDS The MD5 configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 297
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config md5 Purpose Used to enter configure an MD5 key and password. Syntax config md5 Description This command is used to configure an MD5 key and password. Parameters − The MD5 key ID. − An - D-Link DES-3326S | Reference Manual - Page 298
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create md5 Purpose Used to create an MD5 key table. Syntax create md5 key Description This command is used to create an MD5 key table. Parameters − The MD5 key ID. − An MD5 password of up to - D-Link DES-3326S | Reference Manual - Page 299
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete md5 Purpose Used to delete an MD5 key table. Syntax delete md5 key Description This command is used to delete an MD5 key table. Parameters Restrictions − The MD5 key ID. Only administrator-level users can - D-Link DES-3326S | Reference Manual - Page 300
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show md5 Purpose Syntax Description Parameters MD5 key: DES-3326SR:4#show md5 Command: show md5 MD5 Key Table Key-ID -----1 2 3 4 Key ---------- dlink develop fireball intelligent Total Entries: 4 DES-3326SR:4# 300 MD5 - D-Link DES-3326S | Reference Manual - Page 301
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 30 OSPF CONFIGURATION COMMANDS The OSPF configuration commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. - D-Link DES-3326S | Reference Manual - Page 302
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command Param e t e rs config ospf host_route show ospf > area priority hello_interval dead_interval authentication [none/simple / md5 ] 302 OSPF Configuration Commands - D-Link DES-3326S | Reference Manual - Page 303
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command config ospf all show ospf ipif show ospf ipif_name> hello_interval dead_interval authentication [simple /md5 /none] Each command - D-Link DES-3326S | Reference Manual - Page 304
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf Purpose Used to configure the OSPF − The OSPF router ID. Only administrator-level users can issue this command. Usage Example To configure the OSPF router ID: DES-3326SR:4#config ospf router_id 10.48.74.122 Command: config - D-Link DES-3326S | Reference Manual - Page 305
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual enable ospf Purpose Used to enable OSPF on the switch. Syntax enable ospf Description This command, in combination with the disable ospf command below, is used to enable and disable OSPF on the switch. Parameters none. - D-Link DES-3326S | Reference Manual - Page 306
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual disable ospf Purpose Used to disable OSPF on the switch. Syntax disable ospf Description This command, in combination with the enable ospf command above, is used to enable and disable OSPF on the switch. Parameters none. - D-Link DES-3326S | Reference Manual - Page 307
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf Purpose Syntax Description Parameters Restrictions Used to display the current OSPF state on the switch. show ospf This command will display the current state of OSPF on the switch, divided into the following categories: - D-Link DES-3326S | Reference Manual - Page 308
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual OSPF Interface Settings Interface IP Address Area ID -----------System ip2 ip3 10.90.90.90/8 0.0.0.0 20.1.1.1/8 0.0.0.0 30.1.1.1/8 0.0.0.0 State -------Disabled Disabled Disabled Link Metric Status Link DOWN 1 Link DOWN 1 - D-Link DES-3326S | Reference Manual - Page 309
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual OSPF Area Aggregation Settings Area ID Aggregated LSDB Advertise Network Address Type Total Entries : 0 OSPF Host Route Settings Host Address Metric ------ 10.3.3.3 1 Area ID 10.1.1.1 TOS --0 Total Entries : 1 DES- - D-Link DES-3326S | Reference Manual - Page 310
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf area [enabled/disabled]/metric }] between 0 and 65535. The default is 0. Restrictions Only administrator-level users can issue this command. Usage Example: To create an OSPF area: DES-3326SR:4#create ospf area 10.48. - D-Link DES-3326S | Reference Manual - Page 311
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete ospf area Purpose Syntax Description Parameters Used to delete an OSPF area. delete ospf area This command is used to delete an OSPF area. − − A 32-bit number in the form of an IP address (xxx.xxx. - D-Link DES-3326S | Reference Manual - Page 312
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf area Purpose Syntax Description Parameters − The OSPF area stub default cost. Only administrator-level users can issue this command. Usage Example To configure an OSPF area's settings: DES-3326SR:4#config ospf area 10.48 - D-Link DES-3326S | Reference Manual - Page 313
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf area Purpose Syntax Description Parameters Restrictions Used to display an OSPF area's configuration. show ospf area {} This command will display the current - D-Link DES-3326S | Reference Manual - Page 314
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf host_route Purpose Syntax Description Parameters Used to configure OSPF host route settings. create ospf host_route {area /metric } This command is - D-Link DES-3326S | Reference Manual - Page 315
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete ospf host_route Purpose Used to delete an OSPF host route. Syntax delete ospf host_route Description This command is used to delete an OSPF host route. Parameters Restrictions − The IP address of the OSPF - D-Link DES-3326S | Reference Manual - Page 316
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf host_route Purpose Used to configure OSPF host route settings. Syntax config ospf host_route {area /metric } Description This command is used - D-Link DES-3326S | Reference Manual - Page 317
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf host_route Purpose Used to display the Parameters Restrictions − The IP address of the host. none. Usage Example: To display the current OSPF host route table: DES-3326SR:4#show ospf host_route Command: show ospf - D-Link DES-3326S | Reference Manual - Page 318
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf aggregation. − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the Only administrator-level users can issue this command. 318 OSPF Configuration Commands - D-Link DES-3326S | Reference Manual - Page 319
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Usage Example To create an OSPF area aggregation: DES-3326SR:4#create ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Command: create ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary - D-Link DES-3326S | Reference Manual - Page 320
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete ospf aggregation Purpose Used to delete an OSPF area aggregation configuration. Syntax delete ospf aggregation lsdb_type [summary] Description This command is used - D-Link DES-3326S | Reference Manual - Page 321
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Command: delete ospf aggregation 10.1.1.1 10.48.76..122/16 Lsdb_type summary Success. DES-3326SR − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the users can issue this command. OSPF - D-Link DES-3326S | Reference Manual - Page 322
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf aggregation this command. Usage Example To configure the OSPF area aggregation settings: DES-3326SR:4#config ospf aggregation 10.1.1.1 10.48.76.122/16 lsdb_type summary advertise enabled Command: config ospf aggregation 10 - D-Link DES-3326S | Reference Manual - Page 323
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf aggregation Purpose Used to display the current . Restrictions none. Usage Example To display OSPF area aggregation settings: DES-3326SR:4#show ospf aggregation Command: show ospf aggregation OSPF Area Aggregation Settings - D-Link DES-3326S | Reference Manual - Page 324
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf lsdb Purpose Used to display the OSPF Link State Database (LSDB). Syntax show display the current OSPF Link State Database (LSDB). Parameters area_id − A 32-bit number in the form of an IP address (xxx.xxx.xxx - D-Link DES-3326S | Reference Manual - Page 325
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Usage Example To display the link state database of OSPF: DES-3326SR:4#show ospf lsdb Command: show ospf lsdb Area LSDB Advertising Link State Cost Sequence ID Type Router ID ID Number 0.0.0.0 RTRLink 50.48.75.73 50.48.75.73 - D-Link DES-3326S | Reference Manual - Page 326
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf neighbor Purpose Used to display the current OSPF neighbor router table. Syntax show ospf neighbor {} Description This command will display the current OSPF neighbor router table. Parameters − the IP - D-Link DES-3326S | Reference Manual - Page 327
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf virtual neighbor Purpose Used to display virtual neighbor router table. Parameters − A 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the OSPF area in the OSPF domain. < - D-Link DES-3326S | Reference Manual - Page 328
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf ipif Purpose Used to configure the OSPF interface settings. Syntax config ospf ipif {area /priority /hello_interval /dead_interval /authentication [none/simple /md5 - D-Link DES-3326S | Reference Manual - Page 329
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf ipif router before the selected area declares that router down. An interval between 5 and 65535 seconds can be specified. The Dead Interval must be evenly divisible by the Hello Interval. − A case-sensitive - D-Link DES-3326S | Reference Manual - Page 330
3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf all Purpose Used to configure all of the OSPF interfaces on the switch at one time. Syntax config ospf all {area /priority /he llo _i nt e rv al /dead_interval /authentication [none/simple - D-Link DES-3326S | Reference Manual - Page 331
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf all 65535 seconds can be specified. The Dead Interval must be evenly divisible by the Hello Interval. − A case-sensitive password. − A previously configured MD5 key ID (1 to 255). metric − This - D-Link DES-3326S | Reference Manual - Page 332
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf ipif Purpose Used to display the current for a specific OSPF interface: DES-3326SR:4#show ospf ipif2 Command: show ospf ipif2 Interface Name: ipif2 IP Address: 123.234.12.34/24 ((Link Up) Network Medium Type: BROADCAST - D-Link DES-3326S | Reference Manual - Page 333
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf all Purpose Syntax Description Parameters Restrictions Used to display the current OSPF settings of all the OSPF interfaces on the switch. show ospf all This command will display the current OSPF settings for all OSPF - D-Link DES-3326S | Reference Manual - Page 334
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Network Medium Type: BROADCAST Metric: 1 Area ID: 1.0.0.0 Administrative State: Enabled Priority Interval: 40 Transmit Delay: 1 Retransmit Time: 5 Authentication: None Total Entries: 2 DES-3326SR:4# 334 OSPF Configuration Commands - D-Link DES-3326S | Reference Manual - Page 335
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf virtual_link Purpose Used to configure the OSPF virtual interface settings. Syntax config ospf virtual_link {hello_interval /de ad_i nt e rv al /authentication [simple - D-Link DES-3326S | Reference Manual - Page 336
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config ospf virtual_link the receipt of Hello packets from a neighbor router before the selected area declares that router down. An interval between 5 and 65535 seconds - D-Link DES-3326S | Reference Manual - Page 337
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf virtual_link Purpose Used to create an OSPF virtual interface. Syntax Description create ospf virtual_link {hello_interval /authentication [none/simple /md5 ]} This command is - D-Link DES-3326S | Reference Manual - Page 338
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf virtual_link Parameters − A 32-bit number in the form of an IP address (xxx.xxx. − A case-sensitive password. − A previously configured MD5 key ID (1 to 255). Only administrator-level users can - D-Link DES-3326S | Reference Manual - Page 339
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual create ospf virtual_link this command. Usage Example To create an OSPF virtual interface: DES-3326SR:4#create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Command: create ospf virtual_link 10.1.12 20.1.1.1 hello_interval 10 Success - D-Link DES-3326S | Reference Manual - Page 340
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual delete ospf virtual_link − The OSPF router ID for the remote area. This is a 32-bit number in the form of an IP address (xxx.xxx.xxx.xxx) that uniquely identifies the remote area's Area Border Router. The router ID of the - D-Link DES-3326S | Reference Manual - Page 341
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show ospf virtual_link OSPF domain. − The OSPF router ID for the remote area. This is a 32-bit number in the form of an IP : DES-3326SR:4#show ospf virtual_link Transit Virtual Hello Dead Authentication Link Area - D-Link DES-3326S | Reference Manual - Page 342
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual 31 COMMAND HISTORY LIST The switch port commands in the Command Line Interface (CLI) are listed (along with the appropriate parameters) in the following table. Command ? show command_history dir config command_history - D-Link DES-3326S | Reference Manual - Page 343
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual ? Purpose Syntax Description Parameters Restrictions Used all of the commands in the CLI: DES-3326SR:4#? Command: ? clear clear arptable clear counters {ports } clear log clear macentry unicast [vlan | port | - D-Link DES-3326S | Reference Manual - Page 344
-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual show command_history Purpose Syntax Description Parameters Restrictions Used to display the command history. show command_history This command will display the command history. none. none. Usage Example To display the command history: DES - D-Link DES-3326S | Reference Manual - Page 345
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual dir Purpose Syntax Description Parameters Restrictions Used to display all commands. dir This command will display all commands. none. none. Usage Example To display all of the commands: DES-3326SR:4#dir Command: dir . ? clear clear - D-Link DES-3326S | Reference Manual - Page 346
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config dvmrp config gvrp config igmp config igmp snooping config ingress_checking config ipif config ipif System - more - 346 Command History List - D-Link DES-3326S | Reference Manual - Page 347
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual config command_history Purpose Used to configure the command history. Syntax Description config command_history This command is used to configure the command history. Parameters Restrictions < - D-Link DES-3326S | Reference Manual - Page 348
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual A TECHNICAL SPECIFICATIONS Standards: Protocols: Data Transfer Rates: Ethernet Fast Ethernet Gigabit Ethernet Topology: General IEEE 802.3 10BASE-T Ethernet IEEE 802.3u 100BASE-TX Fast Ethernet IEEE 802.3z 1000BASE-SX Gigabit Ethernet - D-Link DES-3326S | Reference Manual - Page 349
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual Network Cables: 10BASE-T: 100BASE-TX: Fiber Optic: Number of Ports: General use SC optical connector 24 x 10/100 Mbps NWay ports 2 Gigabit Ethernet (optional) AC inputs: Power Consumption: DC fans: Operating Temperature: Storage - D-Link DES-3326S | Reference Manual - Page 350
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual EMI: Safety: Physical and Environmental FCC Class A, CE Class A, VCCI Class A, BSMI Class A, C-Tick Class A 1,488,000 pps per port (for 1000Mbps) Automatic update. Max age:10- 9999 seconds. Default = 300. 350 Technical Specifications - D-Link DES-3326S | Reference Manual - Page 351
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual - D-Link DES-3326S | Reference Manual - Page 352
Passport 1424T Layer 3 Fast Ethernet Switch CLI Reference Manual INDEX - D-Link DES-3326S | Reference Manual - Page 353
DES-3326SR Layer 3 Fast Ethernet Switch CLI Reference Manual A AC inputs 375 C Connecting to the Switch VT100-compatible terminal19 V VT100-compatible terminal.. 19 W Weight 375 D Dimensions 375 H Humidity 375 I IP Address 14 IP Addresses and SNMP Community Names 14 M MAC Address - D-Link DES-3326S | Reference Manual - Page 354
Passport 1424T Layer 3 Fast Ethernet Switch CLI Reference Manual
-
1 -
2 -
3 -
4 -
5 -
6 -
7 -
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126
-
127
-
128
-
129
-
130
-
131
-
132
-
133
-
134
-
135
-
136
-
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
-
205
-
206
-
207
-
208
-
209
-
210
-
211
-
212
-
213
-
214
-
215
-
216
-
217
-
218
-
219
-
220
-
221
-
222
-
223
-
224
-
225
-
226
-
227
-
228
-
229
-
230
-
231
-
232
-
233
-
234
-
235
-
236
-
237
-
238
-
239
-
240
-
241
-
242
-
243
-
244
-
245
-
246
-
247
-
248
-
249
-
250
-
251
-
252
-
253
-
254
-
255
-
256
-
257
-
258
-
259
-
260
-
261
-
262
-
263
-
264
-
265
-
266
-
267
-
268
-
269
-
270
-
271
-
272
-
273
-
274
-
275
-
276
-
277
-
278
-
279
-
280
-
281
-
282
-
283
-
284
-
285
-
286
-
287
-
288
-
289
-
290
-
291
-
292
-
293
-
294
-
295
-
296
-
297
-
298
-
299
-
300
-
301
-
302
-
303
-
304
-
305
-
306
-
307
-
308
-
309
-
310
-
311
-
312
-
313
-
314
-
315
-
316
-
317
-
318
-
319
-
320
-
321
-
322
-
323
-
324
-
325
-
326
-
327
-
328
-
329
-
330
-
331
-
332
-
333
-
334
-
335
-
336
-
337
-
338
-
339
-
340
-
341
-
342
-
343
-
344
-
345
-
346
-
347
-
348
-
349
-
350
-
351
-
352
-
353
-
354
 |
 |
i
DES-3326SR
Layer 3 Switch
Command Line Interface
Reference Manual
(April 2003)
DES3326SR
…
1
Printed In Taiwan
RECYCLABLE