Dell Inspiron One 2205 Service Manual - Page 51

Replacing the Antenna

Get Dell Inspiron One 2205 PDF manuals and user guides View all Dell Inspiron One 2205 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 51 highlights

3. Follow the instructions from step 2 to step 3 in Replacing the Antenna-In Connector. 4. Route the antenna-in connector cable and infrared (IR) blaster connector cable through the routing guides on the system-board shield. 5. Connect the IR blaster connector cable to the connector (CIR Receiver) on the system board. 6. Connect the antenna-in connector cable to the connector on the TV tuner card. 7. Carefully turn the system-board shield over and align the screw holes on the system-board shield with the screw holes on the chassis. 8. Replace the four screws that secure the system-board shield to the chassis. 9. Replace the rear stand cover (see Replacing the Rear Stand Cover). 10. Follow the instructions from step 4 to step 7 in Replacing the Front Stand. 11. Replace the back cover (see Replacing the Back Cover). CAUTION: Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may result in damage to the computer. 12. Connect your computer and all attached devices to electrical outlets, and turn them on. Back to Contents Page

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
3.
Follow the instructions from
step 2
to
step 3
in
Replacing the Antenna
-
In Connector
.
4.
Route the antenna-in connector cable and infrared (IR) blaster connector cable through the routing guides on the system-board shield.
5.
Connect the IR blaster connector cable to the connector (CIR Receiver) on the system board.
6.
Connect the antenna-in connector cable to the connector on the TV tuner card.
7.
Carefully turn the system-board shield over and align the screw holes on the system-board shield with the screw holes on the chassis.
8.
Replace the four screws that secure the system-board shield to the chassis.
9.
Replace the rear stand cover (see
Replacing the Rear Stand Cover
).
10.
Follow the instructions from
step 4
to
step 7
in
Replacing the Front Stand
.
11.
Replace the back cover (see
Replacing the Back Cover
).
12.
Connect your computer and all attached devices to electrical outlets, and turn them on.
Back to Contents Page
CAUTION:
Before turning on the computer, replace all screws and ensure that no stray screws remain inside the computer. Failure to do so may
result in damage to the computer.