Electrolux EDW5505E Service Manual - Page 15
Configuration Parameters
View all Electrolux EDW5505E manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 15 highlights
Electrolux EFS - Dishwashing Systems Platform Electrolux Professional Electronic Dishwasher SERVICE MANUAL Prn bt bH tt tH Print parameter table. HACCP 'Basic' (printer) Boiler temperature: high limit. HACCP 'Basic' (printer) Boiler temperature: gap below high limit. HACCP 'Basic' (printer) Tank temperature: high limit. HACCP 'Basic' (printer) Tank temperature: gap below high limit. - 0 1 1 [°C] 45 95 90 [°C] 0 20 10 [°C] 35 75 68 [°C] 0 20 10 CFG Configuration Parameters Sym. Parameter Description Unit Min Max Factory Default tYP Dishwasher Model: 0 = HOOD TYPE & UNDERCOUNTER 1 = POT WASHER 2 = AUTOMATIC POT WASHER - 0 3 0 3 = MEDICAL LINE DISHWASHER WITH LOCK DOOR/HOOD DEVICE boi Boiler type: 0 = ATMOSPHERIC BOILER 1 = PRESSURE BOILER - 0 2 0 2 = EXTERNAL BOILER doo Door type: 0 = AUTOMATIC HOOD 1 = MANUAL HOOD 0 3 1 2 = FRONT LOADING 3 = POT WASHER dFL Default model (see Default tables): 1 = HOOD TYPE 2 = POT WASHER - 0 3 - 3 = UNDERCOUNTER trc Solid State Relay (TRIAC). 0 = not enabled; 1 = SOFT START enabled; - 0 3 0 3 = SLOW SOFT START enabled (works only on boards with Solid State Relay). b_t Boiler/Tank heating swap: 0 = boiler heaters and tank heater can work simultaneously; 1 = swap enabled: tank heating starts only boiler temperature is reached; - 0 1 1 (Note: disabling this function changes the global electrical power of appliance; before enabling this function check available power, supply cable section, fuses in according to User Manual). btF Tank Filling Mode Enable filling tank by means of rinsing cycles. Ex: btF = 75 means that boiler water is heated at 75°C, then follows a [°C] 0 85 75 rinse phase and so on until tank is full. If btF = 0 the tank is filled by solenoid valve in the traditional way. LES Detergent Level Switches 0 = level switches not enabled; - 0 1 0 1 = enable detergent level switches; UI USER INTERFACE MODEL 8 = ACTIVE function disabled (up to version 3.11 [up to serial nr. 42100099] set to 0) 9 = hood type, under counter (up to version 3.11 [up to serial nr. 42100099] set to 1) 13 = LS5 with atmospheric boiler(up to version 3.11 [up to serial nr. - 0 15 9 42100099] set to 5) 15 = LS5 with pressure boiler (user interface without display); (up to version 3.11 [up to serial nr. 42100099] set to 7) See parameter rEL(family ron) to check the software version installed in the board. rE Enable "regeneration cycle" key (only for dishwashers with non-continuous water softener) [See paragraph 9.1 resin regeneration cycle]. - 0 1 0 ALr ALARMS ENABLE 0 = alarms disabled (to disable also warnings see bLo and tLo); 1 = alarms enabled; - 0 1 1 If this function is disabled, faults can be detected so display do not shows any alarm code. DOC. NO. 5956.446.06 ©Copyright 2005 by Electrolux Professional P.15/88