Electrolux EDW5505E Service Manual - Page 8

Counters

Page 8 highlights

Electrolux EFS - Dishwashing Systems Platform Electrolux Professional Electronic Dishwasher SERVICE MANUAL 5. COUNTERS This Parameter Family collects cycle counters and water consumption counters. For water consumption counters a flow meter must be installed. See PPL (calibration parameter) into dPA section (§ Other Parameters). Cnt Counters Sym. Parameter Description Unit Min Max Factory Default CYC Cycles performed counter. CYC symbol and two numbers blink consecutively. The cycle number is obtained by joining the two numbers. Ex. CYC → 10 → 042 means - 10042 cycles executed. cYc Cycle counter (resettable). This counter is similar to CYC but is resettable by user (see rSt parameter - below). nnc Water Consumption. [present up to software version 3.12] Counts m3 of water consumption. [m3] L Water Consumption. [present up to software version 3.12] Counts litres of water consumption. [l] The total consumption is given by adding nnc [m3] and L [l] values. Lit Water Consumption: resettable counter. [present up to software version 3.12] Counts the litres of water and is resettable by user (see rSt parameter below). [l] rSt Reset resettable counters: cYc and Lit To reset put 1 this parameter, switch off and then on again: cYc and Lit will show zero. Note that cYc is used to count cycles for CAll message - (see next parameter, nCY). nCY Store thousand of cycles after that CAll message appears on display. Ex. If this parameter is settled to 20, CAll message appears when cYc - reach 20.000 cycles. drn Drain/Cleaning cycles performed. Similar to CYC but counts Cleaning Cycles. - rCY Numbers of cycles that can be made after a regeneration cycle (only for dishwashers with non-continuous water softener) [See paragraph 9.1 resin - 20 regeneration cycle.]. NRE Regeneration cycle counter (only for water softener dishwasher) [See paragraph 9.1 resin regeneration cycle / paragraph 9.4 Dishwashers with - incorporated continuous water softener]. GEn GEn Cnt Fig.4.1 USER setting mode (press for 5s) CYC Fig.4.2 Next Family 010 Fig. 4.3 Counters Fam.: ENTER 042 cYc Fig. 4.4 CYCLES DOC. NO. 5956.446.06 Fig. 4.5 Thousand. Fig. 4.6 Units. ©Copyright 2005 by Electrolux Professional Fig. 4.7 Next counter. P.8/88

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88

Electrolux
EFS – Dishwashing Systems Platform
Electrolux Professional
Electronic Dishwasher
SERVICE MANUAL
DOC. NO. 5956.446.06
©Copyright 2005 by
Electrolux Professional
P.8/88
5.
COUNTERS
This Parameter Family collects cycle counters and water consumption counters.
For water consumption counters a flow meter must be installed. See
PPL
(calibration parameter) into
dPA
section (§ Other Parameters).
Cnt
Counters
Sym.
Parameter Description
Unit
Min
Max
Factory
Default
CYC
Cycles performed counter.
CYC
symbol and two numbers blink consecutively. The cycle number is
obtained by joining the two numbers. Ex.
CYC
10
042
means
10042 cycles executed.
-
cYc
Cycle counter (resettable).
This counter is similar to
CYC
but is resettable by user (see
rSt
parameter
below).
-
nnc
Water Consumption.
[present up to software version 3.12]
Counts
m
3
of water consumption.
[m
3
]
L
Water Consumption.
[present up to software version 3.12]
Counts
litres
of water consumption.
The total consumption is given by adding
nnc
[m
3
] and
L
[l] values.
[l]
Lit
Water Consumption: resettable counter. [present up to software version 3.12]
Counts the litres of water and is resettable by user (see
rSt
parameter below).
[l]
rSt
Reset resettable counters:
cYc
and
Lit
To reset put 1 this parameter, switch off and then on again:
cYc
and
Lit
will show zero. Note that
cYc
is used to count cycles for
CAll
message
(see next parameter,
nCY
).
-
nCY
Store thousand
of cycles after that
CAll
message appears on display.
Ex. If this parameter is settled to 20,
CAll
message appears when
cYc
reach 20.000 cycles.
-
drn
Drain/Cleaning cycles performed.
Similar to
CYC
but counts Cleaning Cycles.
-
rCY
Numbers of cycles that can be made after a regeneration cycle (only for
dishwashers with non-continuous water softener) [See paragraph
9.1 resin
regeneration cycle.].
-
20
NRE
Regeneration cycle counter (only for water softener dishwasher)
[See paragraph
9.1 resin regeneration cycle / paragraph 9.4 Dishwashers with
incorporated continuous water softener].
-
/
Fig.4.2
Next Family
GEn
/
Fig. 4.3
Counters Fam.:
ENTER
Cnt
Fig. 4.4
CYCLES
CYC
/
/
Fig.4.1
USER setting mode
(press for 5s)
GEn
Fig. 4.5
Thousand.
010
-
Fig. 4.6
Units.
042
-
Fig. 4.7
Next counter.
cYc