HP 4300n HP LaserJet 4200 and 4300 series printer - User Guide - Page 63

Printing on paper with a special finish, FUSER MODES, HIGH 1

Get HP 4300n - LaserJet B/W Laser Printer PDF manuals and user guides
UPC - 808736314381
View all HP 4300n manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Note Printing on paper with a special finish Some paper has a special finish, such as laid paper, bond paper, and cockled paper. These types of paper can cause issues in regard to toner adhesion and print quality. Follow these guidelines when printing on paper with a special finish.  At the printer control panel, open the Configure Device menu. On the Print Quality submenu, select FUSER MODES, and then select the paper type you are using (such as BOND). Set the fuser mode to HIGH 1 or HIGH 2. HIGH 2 provides better toner adhesion and optimal print quality for paper with a highly textured finish. Open the Paper Handling menu and set TRAY TYPE to HIGH 1 or HIGH 2 to enable the fuser mode. The printer might print at a slower speed when set at HIGH 1 or HIGH 2. Use the HIGH 1 and HIGH 2 settings only if you are experiencing toner-adhesion problems. The HIGH 1 and HIGH 2 settings might increase curl and jam problems.  Some makers of these types of paper are now coating one side of the paper to enhance toner adhesion and print quality. To take advantage of this feature, make sure to load the paper correctly. The side on which you can read the watermark correctly is the front side, or the side to be printed. For tray 1, load paper with the front side facing up, and the top, short edge toward the printer. Orientation for tray 1 For tray 2, optional 500-sheet trays, and the optional 1,500-sheet tray, load paper with the front side facing down, and the top, short edge toward you. Orientation for all other trays ENWW Printing special paper 61

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
  • 205
  • 206
  • 207
  • 208
  • 209
  • 210
  • 211
  • 212
  • 213
  • 214
  • 215
  • 216
  • 217
  • 218
ENWW
Printing special paper
61
Printing on paper with a special finish
Some paper has a special finish, such as laid paper, bond paper, and cockled paper. These
types of paper can cause issues in regard to toner adhesion and print quality. Follow these
guidelines when printing on paper with a special finish.
At the printer control panel, open the Configure Device menu. On the Print Quality submenu,
select
FUSER MODES
, and then select the paper type you are using (such as
BOND
). Set the
fuser mode to
HIGH 1
or
HIGH 2
.
HIGH 2
provides better toner adhesion and optimal print
quality for paper with a highly textured finish. Open the Paper Handling menu and set
TRAY
TYPE
to
HIGH 1
or
HIGH 2
to enable the fuser mode.
Note
The printer might print at a slower speed when set at
HIGH 1
or
HIGH 2
.
Use the
HIGH 1
and
HIGH 2
settings only if you are experiencing toner-adhesion problems. The
HIGH 1
and
HIGH 2
settings might increase curl and jam problems.
Some makers of these types of paper are now coating one side of the paper to enhance
toner adhesion and print quality. To take advantage of this feature, make sure to load the
paper correctly. The side on which you can read the watermark correctly is the front side, or
the side to be printed.
For tray 1, load paper with the front side facing up, and the top, short edge toward the
printer.
For tray 2, optional 500-sheet trays, and the optional 1,500-sheet tray, load paper with the
front side facing down, and the top, short edge toward you.
Orientation for tray 1
Orientation for all other trays