HP Model 715/100 hp 9000 series 700 model 715 workstations service handbook (a - Page 20

System Unit Rear Panel Connectors

Get HP Model 715/100 - Workstation PDF manuals and user guides View all HP Model 715/100 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 20 highlights

System Unit Rear Panel Connectors This section describes the following connectors on the system unit's rear panel: S SCSI connector S HP parallel I/O connector S HP-HIL connector (Model 715/C, 715/33, 715/50, and 715/75 workstations) S 10-pin modular jack (Model 715/64, 715/80, 715/100, and 715/100XC workstations) S RS-232 serial input/output connectors S 802.3 network connector S Built-in graphics connector S Optional connector for EISA, CRX, or HCRX graphics S Power cord connector S Audio connectors NOTICE: To maintain FCC/EMI compliance, verify that all cables are fully seated and properly fastened. Figure 1-3 shows the locations of the connectors on the system unit's rear panel. The symbols shown are depicted on the rear panel. Product Information 1-7

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
Product Information
1–7
System Unit Rear Panel Connectors
This section describes the following connectors on the system unit’s rear panel:
S
SCSI connector
S
HP parallel I/O connector
S
HP–HIL connector (Model
715/C, 715/33, 715/50, and 715/75 workstations)
S
10–pin modular jack (Model 715/64, 715/80, 715/100, and 715/100XC
workstations)
S
RS–232 serial input/output connectors
S
802.3 network connector
S
Built–in graphics connector
S
Optional connector for EISA, CRX, or HCRX graphics
S
Power cord connector
S
Audio connectors
NOTICE:
To maintain FCC/EMI compliance, verify that all
cables are fully seated and properly fastened.
Figure 1–3 shows the locations of the connectors on the system unit’s rear panel. The
symbols shown are depicted on the rear panel.