Home » HP Manuals » Storage Devices » HP StorageWorks 2/16V » Manual Viewer

HP StorageWorks 2/16V HP StorageWorks SAN Switch 2/8V, 2/16V, 2/16N and 4/32 I - Page 107

Fibre Channel port specifications, 2/8V, Serial port specifications, 8V

View all HP StorageWorks 2/16V manuals

Add to My Manuals
Save this manual to your list of manuals

Page 107 highlights

Fibre Channel port specifications The following sections summarize Fibre Channel Port specifications. 2/8V, 2/16V and 2/16N Fibre Channel port specifications The Fibre Channel ports in the 2/8V, 2/16V and 2/16N are compatible with SWL and LWL SFP transceivers. The strength of the signal is determined by the type of transceiver in use. The ports operate at 2.125 Gb/sec or 1.0625 Gb/sec, and autosense to the highest speed of all attached devices. 4/32 Fibre Channel port specifications The Fibre Channel ports in the SAN Switch 4/32 are compatible with SWL, LWL, and ELWLW SFP transceivers. The strength of the signal is determined by the type of transceiver in use. The ports are capable of operating at 1, 2, or 4 Gbps and are able to autonegotiate to the higher of 1 or 2 Gbps. Operation at 4 Gbps must be set manually. Serial port specifications The serial port is located on the port side of the switch. It is a three-wire RS-232 port with a DB-9 male connector, designed to connect to a DTE port. NOTE: To protect the serial port from dust and ESD, keep the cover in place on the serial port when the port is not in use. The serial port can connect to a computer workstation to configure the switch IP address without connecting to the fabric. The serial port's parameters are fixed at 9600 baud, 8 data bits, and no parity, with flow control set to None. The port requires a straight serial cable with a female 9-pin subminiature-D connector. Only pins 2, 3, and 5 are supported. SAN Switch 2/8V, 2/16V, 2/16N and 4/32 installation guide 107

Section	Page
Contents	3
About this guide	9
Overview	10
Intended audience	10
Related documentation	10
Conventions	11
Document conventions	11
Document conventions	11
Text symbols	12
Equipment symbols	13
Rack stability	14
Getting help	14
HP technical support	14
HP Storage web site	15
HP authorized reseller	15
Overview	17
SAN Switch 2/8V, 2/16V and 2/16N models	18
SAN Switch 2/8V, 2/16V and 2/16N features	18
SAN Switch 2/8V, 2/16V and 2/16N chassis	19
SAN Switch 2/8V, 2/16V and 2/16N-port side	19
Figure 1 Port side of SAN Switch 2/8V	19
Table 1 SAN Switch 2/8V port side components	19
Figure 2 Port side of SAN Switch 2/16V and 2/16N	20
Table 2 SAN Switch 2/16V and 2/16N port side components	20
SAN Switch 2/8V, 2/16V and 2/16N-nonport side	20
SAN Switch 4/32 models	21
SAN Switch 4/32 features	21
SAN Switch 4/32 chassis	22
SAN Switch 4/32-port side	22
Figure 3 Port side of SAN Switch 4/32	22
Table 3 SAN Switch 4/32 port side components (continued)	22
SAN Switch 4/32-nonport side	23
Figure 4 SAN Switch 4/32-nonport side	23
Table 4 SAN Switch 4/32 nonport side components	24
Upgrading SAN Switch 4/32 ports	24
SAN Switch licensing	25
ISL Trunking groups	26
Figure 5 Trunking groups	26
SAN Switch supported (optional) features	27
SAN Switch optional kits	28
Table 5 Optional kits (continued)	28
Installing and configuring	31
SAN Switch shipping carton contents	32
Figure 6 SAN Switch shipping carton contents	32
SAN Switch shipping carton contents checklist	32
Table 6 SAN Switch shipping carton contents checklist	33
Installation and safety considerations	34
Electrical considerations	34
Environmental considerations	34
Rack specifications	35
Cooling considerations	35
Installing as a stand-alone device	36
Installing the switch in a rack using the SAN Switch Rack Mount Kit	37
Table 7 SAN Switch Rack Mount Kit hardware (continued)	38
Figure 7 Installing the rear mounting brackets (HP 10,000 series)	40
Figure 8 Installing the rear mounting brackets (HP System/e rack-left rear upright)	41
Figure 9 Installing the outer rails (HP 10,000 series)	42
Figure 10 Assembling the outer rails (HP 10,000 series)	43
Figure 11 Assembling the outer rails (HP System/e rack)	44
Table 8 Number of screws required to assemble the inner rails	45
Figure 12 Securing the inner rails to the SAN Switch 2/8V with plenum	46
Figure 13 Securing the inner rails to the SAN Switch 2/16V	47
Figure 14 Securing the inner rails to the SAN Switch 4/32	47
Figure 15 Installing the switch into a rack (HP 10,000 series rack)	48
Figure 16 Installing the switch into a rack (HP System/e rack)	49
Cabling and configuring the SAN Switch	50
Recommendations for cable management	50
Connecting the SAN Switch to the fabric	51
Items required	51
Making a serial connection	51
Figure 17 Connecting the serial cable to a SAN Switch 2/16V	52
Logging in	53
Figure 18 Connecting SAN Switch 2/16V power cords	53
Setting the IP address	54
Creating an Ethernet connection	55
Figure 19 Connecting the Ethernet cable to the SAN Switch 2/16V	55
Modifying the Fibre Channel domain ID (Optional)	56
Installing the SFP transceivers	57
Connecting the cables	57
Verifying the configuration	58
Backing up the configuration	58
Setting the switch date and time	58
Synchronizing local time with an external source	59
Correcting the time zone of a switch	59
Table 9 tsTimeZone command parameter selection	60
Managing SAN switches	61
Powering on and off	62
SAN Switch 2/8V	62
SAN Switch 2/16V, 2/16N and 4/32	62
Management features	63
Table 10 Management options	63
Managing SAN Switches from a single management station	64
Interpreting LED activity	64
SAN Switch 2/8V, 2/16V and 2/16N LEDs	65
Figure 20 SAN Switch 2/8V LED locations	65
Table 11 SAN Switch 2/8V LED Locations	65
Figure 21 SAN Switch 2/16V and 2/16N LED locations	66
Table 12 SAN Switch 2/16V and 2/16N LED locations	66
SAN Switch 2/8V, 2/16V and 2/16N LED patterns	67
System and power LED patterns	67
Table 13 System LED patterns during normal operation	67
Port LED patterns	68
Table 14 Port LED patterns during normal operation (continued)	68
Ethernet LED patterns	69
Table 15 Ethernet LED patterns	69
SAN Switch 4/32 LEDs-port side	70
Figure 22 SAN Switch 4/32 port side LEDs	71
Table 16 SAN Switch 4/32 port side LEDs	71
Table 17 SAN Switch 4/32 port side LED patterns during normal operation (continued)	72
SAN Switch 4/32 LEDs-nonport side	74
Figure 23 SAN Switch 4/32 nonport side LEDs	74
Table 18 SAN Switch 4/32 nonport side LEDs	74
Table 19 Nonport side LED patterns during normal operation	75
POST and boot specifications	76
POST	76
Boot	76
Interpreting POST results	77
Diagnostic tests	77
Installing field-replaceable units	79
Replacing the SAN Switch 4/32 power supply	80
Figure 24 SAN Switch 4/32 power supplies on the nonport side	80
Table 20 SAN Switch 4/32 nonport side LEDs (continued)	80
Table 21 Power supply status LEDs	81
Items required	82
Procedure	82
Figure 25 Inserting the power supply in the SAN Switch 4/32	83
Table 22 Power supply components	83
Replacing the fan assembly in the SAN Switch 4/32	85
Figure 26 SAN Switch 4/32 fan assemblies on the nonport side	85
Table 23 Fan assemblies	85
Table 24 Fan status LED behavior	86
Items required	87
Procedure	87
Figure 27 Inserting the fan assembly	88
Table 25 Fan assemblies	88
Replacing SFPs	89
Figure 28 Installing or removing an SFP	90
Regulatory compliance notices	91
FCC EMC statement (USA)	91
EMC statement (Canada)	92
EMC statement (European Union)	92
European union notice	92
Germany noise declaration	92
VCCI EMC statement (Japan)	93
Japanese power cord statement	93
RRL EMC statement (Korea)	94
Laser safety	95
Battery replacement notice	96
Electrostatic discharge	97
Grounding methods	97
SAN Switch technical specifications	99
General specifications	100
Table 26 General specifications (continued)	100
Weight and physical dimensions	102
Table 27 SAN Switch specifications	102
Facility requirements	103
Table 28 Facility requirements	103
Environmental requirements	104
Table 29 Environmental requirements	104
Data transmission ranges	105
Data transmissions for the 2/8V, 2/16V and 2/16N	105
Table 30 Laser data transmission ranges for the 2/8V, 2/16V and 2/16N	105
Data transmissions for the 4/32	105
Table 31 Laser data transmission ranges for the 4/32 (continued)	105
Fibre Channel port specifications	107
2/8V, 2/16V and 2/16N Fibre Channel port specifications	107
4/32 Fibre Channel port specifications	107
Serial port specifications	107
Table 32 Cabling pinouts	108
Power supply specifications	109
Table 33 Power supply specifications (continued)	109
Memory	110
Table 34 2/8V, 2/16V and 2/16N Memory specifications	110
Table 35 4/32 Memory specifications	111
Supported SFPs	111
Supported HBAs	111
Glossary	113
Index	123
A	123
B	123
C	123
D	123
E	123
F	124
G	124
H	124
I	124
L	124
M	124
N	124
O	124
P	125
R	125
S	125
T	125
U	126
V	126
W	126

Match case Limit results 1 per page

107

SAN Switch 2/8V, 2/16V, 2/16N and 4/32 installation guide

Fibre Channel port specifications

The following sections summarize Fibre Channel Port specifications.

2/8V, 2/16V and 2/16N Fibre Channel port

specifications

The Fibre Channel ports in the 2/8V, 2/16V and 2/16N are compatible with SWL and LWL

SFP transceivers. The strength of the signal is determined by the type of transceiver in use.

The ports operate at 2.125 Gb/sec or 1.0625 Gb/sec, and autosense to the highest speed of

all attached devices.

4/32 Fibre Channel port specifications

The Fibre Channel ports in the SAN Switch 4/32 are compatible with SWL, LWL, and ELWLW

SFP transceivers. The strength of the signal is determined by the type of transceiver in use.

The ports are capable of operating at 1, 2, or 4 Gbps and are able to autonegotiate to the

higher of 1 or 2 Gbps. Operation at 4 Gbps must be set manually.

Serial port specifications

The serial port is located on the port side of the switch. It is a three-wire RS–232 port with a

DB–9 male connector, designed to connect to a DTE port.

NOTE:

To protect the serial port from dust and ESD, keep the cover in place on the serial port

when the port is not in use.

The serial port can connect to a computer workstation to configure the switch IP address

without connecting to the fabric. The serial port’s parameters are fixed at 9600 baud, 8 data

bits, and no parity, with flow control set to

None

The port requires a straight serial cable with a female 9-pin subminiature-D connector. Only

pins 2, 3, and 5 are supported.