Home » HP Manuals » Storage Devices » HP StorageWorks 2/16V » Manual Viewer

HP StorageWorks 2/16V HP StorageWorks SAN Switch 2/8V, 2/16V, 2/16N and 4/32 I - Page 95

Laser safety

View all HP StorageWorks 2/16V manuals

Add to My Manuals
Save this manual to your list of manuals

Page 95 highlights

Laser safety A. Certification and Classification Information When equipped with native Fibre Channel adapters, this product contains a laser internal to the small form factor pluggable (SFP) transceiver modules. In the USA, the SFP module is certified as a Class 1 Laser product, conforming to the requirements contained in Department Of Health and Human Services (DHHS) regulation 21 CFR, Subchapter J. The certification is indicated by a label on the metal SFP housing. Outside the USA, the SFP is certified as a Class 1 Laser product conforming to requirements contained in IEC 825-1:1993 and EN60825-1:1994, including Amendment 11:1996. The SFP includes the following certifications: • UL Recognized Component (USA) • CSA Certified Component (Canada) • TUV Certified Component (European Union) • CB Certificate (Worldwide) The following figure shows the Class 1 information label that appears on the metal housing of the SFP. CLASS 1 LASER PRODUCT 21 CFR(J) B. Product Information Each communications port consists of a transmitter and receiver optical subassembly. The transmitter subassembly contains internally a semiconductor laser diode in the wavelength of either 850 nanometers (shortwave laser) or 1310 nanometers (longwave laser). Class 1 Laser products are not considered hazardous. C. Usage Restrictions Failure to comply with these usage restrictions may result in incorrect operation of the system and points of access may emit laser radiation above the Class 1 limits established by the IEC and U.S. DHHS. SAN Switch 2/8V, 2/16V, 2/16N and 4/32 installation guide 95

Section	Page
Contents	3
About this guide	9
Overview	10
Intended audience	10
Related documentation	10
Conventions	11
Document conventions	11
Document conventions	11
Text symbols	12
Equipment symbols	13
Rack stability	14
Getting help	14
HP technical support	14
HP Storage web site	15
HP authorized reseller	15
Overview	17
SAN Switch 2/8V, 2/16V and 2/16N models	18
SAN Switch 2/8V, 2/16V and 2/16N features	18
SAN Switch 2/8V, 2/16V and 2/16N chassis	19
SAN Switch 2/8V, 2/16V and 2/16N-port side	19
Figure 1 Port side of SAN Switch 2/8V	19
Table 1 SAN Switch 2/8V port side components	19
Figure 2 Port side of SAN Switch 2/16V and 2/16N	20
Table 2 SAN Switch 2/16V and 2/16N port side components	20
SAN Switch 2/8V, 2/16V and 2/16N-nonport side	20
SAN Switch 4/32 models	21
SAN Switch 4/32 features	21
SAN Switch 4/32 chassis	22
SAN Switch 4/32-port side	22
Figure 3 Port side of SAN Switch 4/32	22
Table 3 SAN Switch 4/32 port side components (continued)	22
SAN Switch 4/32-nonport side	23
Figure 4 SAN Switch 4/32-nonport side	23
Table 4 SAN Switch 4/32 nonport side components	24
Upgrading SAN Switch 4/32 ports	24
SAN Switch licensing	25
ISL Trunking groups	26
Figure 5 Trunking groups	26
SAN Switch supported (optional) features	27
SAN Switch optional kits	28
Table 5 Optional kits (continued)	28
Installing and configuring	31
SAN Switch shipping carton contents	32
Figure 6 SAN Switch shipping carton contents	32
SAN Switch shipping carton contents checklist	32
Table 6 SAN Switch shipping carton contents checklist	33
Installation and safety considerations	34
Electrical considerations	34
Environmental considerations	34
Rack specifications	35
Cooling considerations	35
Installing as a stand-alone device	36
Installing the switch in a rack using the SAN Switch Rack Mount Kit	37
Table 7 SAN Switch Rack Mount Kit hardware (continued)	38
Figure 7 Installing the rear mounting brackets (HP 10,000 series)	40
Figure 8 Installing the rear mounting brackets (HP System/e rack-left rear upright)	41
Figure 9 Installing the outer rails (HP 10,000 series)	42
Figure 10 Assembling the outer rails (HP 10,000 series)	43
Figure 11 Assembling the outer rails (HP System/e rack)	44
Table 8 Number of screws required to assemble the inner rails	45
Figure 12 Securing the inner rails to the SAN Switch 2/8V with plenum	46
Figure 13 Securing the inner rails to the SAN Switch 2/16V	47
Figure 14 Securing the inner rails to the SAN Switch 4/32	47
Figure 15 Installing the switch into a rack (HP 10,000 series rack)	48
Figure 16 Installing the switch into a rack (HP System/e rack)	49
Cabling and configuring the SAN Switch	50
Recommendations for cable management	50
Connecting the SAN Switch to the fabric	51
Items required	51
Making a serial connection	51
Figure 17 Connecting the serial cable to a SAN Switch 2/16V	52
Logging in	53
Figure 18 Connecting SAN Switch 2/16V power cords	53
Setting the IP address	54
Creating an Ethernet connection	55
Figure 19 Connecting the Ethernet cable to the SAN Switch 2/16V	55
Modifying the Fibre Channel domain ID (Optional)	56
Installing the SFP transceivers	57
Connecting the cables	57
Verifying the configuration	58
Backing up the configuration	58
Setting the switch date and time	58
Synchronizing local time with an external source	59
Correcting the time zone of a switch	59
Table 9 tsTimeZone command parameter selection	60
Managing SAN switches	61
Powering on and off	62
SAN Switch 2/8V	62
SAN Switch 2/16V, 2/16N and 4/32	62
Management features	63
Table 10 Management options	63
Managing SAN Switches from a single management station	64
Interpreting LED activity	64
SAN Switch 2/8V, 2/16V and 2/16N LEDs	65
Figure 20 SAN Switch 2/8V LED locations	65
Table 11 SAN Switch 2/8V LED Locations	65
Figure 21 SAN Switch 2/16V and 2/16N LED locations	66
Table 12 SAN Switch 2/16V and 2/16N LED locations	66
SAN Switch 2/8V, 2/16V and 2/16N LED patterns	67
System and power LED patterns	67
Table 13 System LED patterns during normal operation	67
Port LED patterns	68
Table 14 Port LED patterns during normal operation (continued)	68
Ethernet LED patterns	69
Table 15 Ethernet LED patterns	69
SAN Switch 4/32 LEDs-port side	70
Figure 22 SAN Switch 4/32 port side LEDs	71
Table 16 SAN Switch 4/32 port side LEDs	71
Table 17 SAN Switch 4/32 port side LED patterns during normal operation (continued)	72
SAN Switch 4/32 LEDs-nonport side	74
Figure 23 SAN Switch 4/32 nonport side LEDs	74
Table 18 SAN Switch 4/32 nonport side LEDs	74
Table 19 Nonport side LED patterns during normal operation	75
POST and boot specifications	76
POST	76
Boot	76
Interpreting POST results	77
Diagnostic tests	77
Installing field-replaceable units	79
Replacing the SAN Switch 4/32 power supply	80
Figure 24 SAN Switch 4/32 power supplies on the nonport side	80
Table 20 SAN Switch 4/32 nonport side LEDs (continued)	80
Table 21 Power supply status LEDs	81
Items required	82
Procedure	82
Figure 25 Inserting the power supply in the SAN Switch 4/32	83
Table 22 Power supply components	83
Replacing the fan assembly in the SAN Switch 4/32	85
Figure 26 SAN Switch 4/32 fan assemblies on the nonport side	85
Table 23 Fan assemblies	85
Table 24 Fan status LED behavior	86
Items required	87
Procedure	87
Figure 27 Inserting the fan assembly	88
Table 25 Fan assemblies	88
Replacing SFPs	89
Figure 28 Installing or removing an SFP	90
Regulatory compliance notices	91
FCC EMC statement (USA)	91
EMC statement (Canada)	92
EMC statement (European Union)	92
European union notice	92
Germany noise declaration	92
VCCI EMC statement (Japan)	93
Japanese power cord statement	93
RRL EMC statement (Korea)	94
Laser safety	95
Battery replacement notice	96
Electrostatic discharge	97
Grounding methods	97
SAN Switch technical specifications	99
General specifications	100
Table 26 General specifications (continued)	100
Weight and physical dimensions	102
Table 27 SAN Switch specifications	102
Facility requirements	103
Table 28 Facility requirements	103
Environmental requirements	104
Table 29 Environmental requirements	104
Data transmission ranges	105
Data transmissions for the 2/8V, 2/16V and 2/16N	105
Table 30 Laser data transmission ranges for the 2/8V, 2/16V and 2/16N	105
Data transmissions for the 4/32	105
Table 31 Laser data transmission ranges for the 4/32 (continued)	105
Fibre Channel port specifications	107
2/8V, 2/16V and 2/16N Fibre Channel port specifications	107
4/32 Fibre Channel port specifications	107
Serial port specifications	107
Table 32 Cabling pinouts	108
Power supply specifications	109
Table 33 Power supply specifications (continued)	109
Memory	110
Table 34 2/8V, 2/16V and 2/16N Memory specifications	110
Table 35 4/32 Memory specifications	111
Supported SFPs	111
Supported HBAs	111
Glossary	113
Index	123
A	123
B	123
C	123
D	123
E	123
F	124
G	124
H	124
I	124
L	124
M	124
N	124
O	124
P	125
R	125
S	125
T	125
U	126
V	126
W	126

Match case Limit results 1 per page

SAN Switch 2/8V, 2/16V, 2/16N and 4/32 installation guide

Laser safety

A. Certification and Classification Information

When equipped with native Fibre Channel adapters, this product contains a laser internal to

the small form factor pluggable (SFP) transceiver modules.

In the USA, the SFP module is certified as a Class 1 Laser product, conforming to the

requirements contained in Department Of Health and Human Services (DHHS) regulation 21

CFR, Subchapter J. The certification is indicated by a label on the metal SFP housing.

Outside the USA, the SFP is certified as a Class 1 Laser product conforming to requirements

contained in IEC 825-1:1993 and EN60825-1:1994, including Amendment 11:1996.

The SFP includes the following certifications:

•

UL Recognized Component (USA)

•

CSA Certified Component (Canada)

•

TUV Certified Component (European Union)

•

CB Certificate (Worldwide)

The following figure shows the Class 1 information label that appears on the metal housing of

the SFP.

B. Product Information

Each communications port consists of a transmitter and receiver optical subassembly. The

transmitter subassembly contains internally a semiconductor laser diode in the wavelength of

either 850 nanometers (shortwave laser) or 1310 nanometers (longwave laser).

Class 1 Laser products are not considered hazardous.

C. Usage Restrictions

Failure to comply with these usage restrictions may result in incorrect operation of the system

and points of access may emit laser radiation above the Class 1 limits established by the IEC

and U.S. DHHS.

CLASS 1 LASER PRODUCT 21 CFR(J)