HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 131

PCI-X Hot-Plug LED OL* LEDs, Disk Drive LEDs, LAN Default Parameters

Page 131 highlights

Table 5-7 Core I/O Buttons Button Identification (as Location silk-screened on the bulkhead) Function MP RESET Center of the core I/O card Resets the MP NOTE: If the MP RESET button is held for longer than five seconds, it will clear the MP password and reset the LAN, RS-232 (serial port), and modem port parameters to their default values. LAN Default Parameters • IP Address-192.168.1.1 • Subnet mask-255.255.255.0 • Default gateway-192.168.1.1 • Hostname-gsp0 RS-232 (Serial Port) Default Parameters • 9600 baud • 8 bits • No parity OLR (Symbol next to Top end of the core I/O card Request OL* for this core I/O slot button is shown below) NOTE: The OLR function is not enabled for the core I/O card. PCI-X Hot-Plug LED OL* LEDs Table 5-8 OL* LED States State Normal operation, slot power on Slot selected, slot power on Slot needs attention, slot power on Slot available, slot power off Ready for OL*, slot power off Fault detected, slot power off Slot powering down or up Power (Green) On On On Off Off Off Flashing Disk Drive LEDs There are two tri-color LED on each disk drive. Attention (Yellow) Off Flashing On Off Flashing On Off Server LED Indicators 131

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195

Table 5-7 Core I/O Buttons
Function
Location
Button Identification (as
silk-screened on the
bulkhead)
Resets the MP
NOTE:
If the MP RESET button is held for longer than five
seconds, it will clear the MP password and reset the LAN,
RS-232 (serial port), and modem port parameters to their
default values.
LAN Default Parameters
IP Address—192.168.1.1
Subnet mask—255.255.255.0
Default gateway—192.168.1.1
Hostname—gsp0
RS-232 (Serial Port) Default Parameters
9600 baud
8 bits
No parity
Center of the core I/O card
MP RESET
Request OL* for this core I/O slot
NOTE:
The OLR function is not enabled for the core I/O card.
Top end of the core I/O card
OLR (Symbol next to
button is shown below)
PCI-X Hot-Plug LED OL* LEDs
Table 5-8 OL* LED States
Attention (Yellow)
Power (Green)
State
Off
On
Normal operation, slot power on
Flashing
On
Slot selected, slot power on
On
On
Slot needs attention, slot power on
Off
Off
Slot available, slot power off
Flashing
Off
Ready for OL*, slot power off
On
Off
Fault detected, slot power off
Off
Flashing
Slot powering down or up
Disk Drive LEDs
There are two tri-color LED on each disk drive.
Server LED Indicators
131