HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 159

Single SCSI and Power Cable in Drive Bay, SCSI and Power Cable Lengths

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 159 highlights

Figure 6-18 Single SCSI and Power Cable in Drive Bay Top DVD/DAT SCSI Cable Single Removable Media Power Cable The following procedure provides information on configuring the removable media drive bay cables for use with the half-height DVD or DAT drive. 1. Turn off power and remove the top cover. 2. If the cable configuration appears as shown in Figure 6-18 with one power cable and the Top DVD/DAT data cable, proceed with the installation of the drive as described in "Installing the Half-Height DVD or DAT drive" (page 160). 3. Move the SCSI cables that connect to the mass storage backplane out of the way. 4. Move the removable media data cables out of the way. 5. Remove the metal removable media bay cover. 6. Carefully unfold the Bottom DVD data cable at the bends marked with green and unnest from the Top DVD/DAT cable. 7. Locate the data cable labeled Top DVD/DAT. This cable must be used for a DVD or DAT drive. 8. Carefully fold the Top DVD/DAT data cable and insert it into the media bay. The cable must extend out of the drive bay so the black line aligns with the front of the chassis. The cable terminator remains outside of the drive bay in the top of the chassis. 9. Insert one power cable into the drive bay to the right of the data cable as shown in Figure 6-19. The power cable must extend out of the drive bay so the red flag on the red wire aligns with the front of the chassis. See Figure 6-19. Figure 6-19 SCSI and Power Cable Lengths Black Line on SCSI Data Cable Red Cable Length Flag Installing a Half-Height DVD or DAT Drive. 159

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
Figure 6-18 Single SCSI and Power Cable in Drive Bay
Single Removable
Media Power Cable
Top DVD/DAT
SCSI Cable
The following procedure provides information on configuring the removable media drive bay
cables for use with the half-height DVD or DAT drive.
1.
Turn off power and remove the top cover.
2.
If the cable configuration appears as shown in
Figure 6-18
with one power cable and the
Top DVD/DAT
data cable, proceed with the installation of the drive as described in
“Installing
the Half-Height DVD or DAT drive” (page 160)
.
3.
Move the SCSI cables that connect to the mass storage backplane out of the way.
4.
Move the removable media data cables out of the way.
5.
Remove the metal removable media bay cover.
6.
Carefully unfold the
Bottom DVD
data cable at the bends marked with green and unnest
from the
Top DVD/DAT
cable.
7.
Locate the data cable labeled
Top DVD/DAT
. This cable must be used for a DVD or DAT
drive.
8.
Carefully fold the
Top DVD/DAT
data cable and insert it into the media bay. The cable must
extend out of the drive bay so the black line aligns with the front of the chassis. The cable
terminator remains outside of the drive bay in the top of the chassis.
9.
Insert one power cable into the drive bay to the right of the data cable as shown in
Figure 6-19
.
The power cable must extend out of the drive bay so the red flag on the red wire aligns with
the front of the chassis. See
Figure 6-19
.
Figure 6-19 SCSI and Power Cable Lengths
Red Cable Length Flag
Black Line on SCSI Data Cable
Installing a Half-Height DVD or DAT Drive.
159