HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 59

Removable Media Drive Installation, Disk Drive and DVD Drive Location

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 59 highlights

Figure 3-17 Disk Drive and DVD Drive Location DVD/DAT/ Slimline DVD Drive Path: 1/0/0/3/1.2.0 Slimline DVD Drive Path: 0/0/0/3/1.2.0 Drive 1-1 Path: 1/0/0/3/0.6.0 Drive 1-2 Path: 1/0/1/1/0/4/1.6.0 Drive 0-2 Path: 0/0/1/1/0/4/1.5.0 Drive 0-1 Path: 0/0/0/3/0.6.0 Use the following procedure to install the disk drives: 1. Be sure the front locking latch is open, then position the disk drive in the chassis. 2. Slide the disk drive into the chassis, a slow firm pressure is needed to properly seat the connector. 3. Press the front locking latch to secure the disk drive in the chassis. 4. If the server OS is running, spin up the disk by entering one of the following commands: #diskinfo -v /dev/rdsk/cxtxdx #ioscan -f Removable Media Drive Installation The DVD drive, or DAT tape drive is located in the left front of the chassis. The server power must be turned off before installation. See Chapter 4: Booting and Shutting Down the Operating System, see "Powering Off Hardware Components and Powering On the Server" (page 142), and see "Removing and Replacing a Half-Height DVD/DAT Drive" (page 156). Installing Additional Cards and Storage 59

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
Figure 3-17 Disk Drive and DVD Drive Location
Drive 1-1
Path: 1/0/0/3/0.6.0
Drive 1-2
Path: 1/0/1/1/0/4/1.6.0
Drive 0-2
Path: 0/0/1/1/0/4/1.5.0
Drive 0-1
Path: 0/0/0/3/0.6.0
DVD/DAT/
Slimline DVD Drive
Path: 1/0/0/3/1.2.0
Slimline DVD Drive
Path: 0/0/0/3/1.2.0
Use the following procedure to install the disk drives:
1.
Be sure the front locking latch is open, then position the disk drive in the chassis.
2.
Slide the disk drive into the chassis, a slow firm pressure is needed to properly seat the
connector.
3.
Press the front locking latch to secure the disk drive in the chassis.
4.
If the server OS is running, spin up the disk by entering one of the following commands:
#diskinfo -v /dev/rdsk/cxtxdx
#ioscan -f
Removable Media Drive Installation
The DVD drive, or DAT tape drive is located in the left front of the chassis. The server power
must be turned off before installation. See
Chapter 4: Booting and Shutting Down the Operating
System
, see
“Powering Off Hardware Components and Powering On the Server” (page 142)
, and
see
“Removing and Replacing a Half-Height DVD/DAT Drive” (page 156)
.
Installing Additional Cards and Storage
59