HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 145

Replacing the Top Cover, Removing and Replacing a Side Cover, Electrostatic Discharge,

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 145 highlights

1. Connect to ground with a wrist strap and grounding mat. Refer to "Electrostatic Discharge " (page 142) for more information. 2. Loosen the retaining screws securing the cover to the rear of the chassis. 3. Slide the cover toward the rear of the chassis. 4. Lift the cover up and away from the chassis. Replacing the Top Cover 1. Orient the cover on the top of the chassis. NOTE: Carefully seat the cover to avoid damage to the intrusion switch. 2. Slide the cover into position using a slow firm pressure to properly seat the cover. 3. Tighten the retaining screws to secure the cover to the chassis. Removing and Replacing a Side Cover It is necessary to remove and replace one or both of the side covers to access the components within the server chassis. Figure 6-3 Side Cover Locations Removing and Replacing a Side Cover 145

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
1.
Connect to ground with a wrist strap and grounding mat. Refer to
“Electrostatic Discharge
” (page 142)
for more information.
2.
Loosen the retaining screws securing the cover to the rear of the chassis.
3.
Slide the cover toward the rear of the chassis.
4.
Lift the cover up and away from the chassis.
Replacing the Top Cover
1.
Orient the cover on the top of the chassis.
NOTE:
Carefully seat the cover to avoid damage to the intrusion switch.
2.
Slide the cover into position using a slow firm pressure to properly seat the cover.
3.
Tighten the retaining screws to secure the cover to the chassis.
Removing and Replacing a Side Cover
It is necessary to remove and replace one or both of the side covers to access the components
within the server chassis.
Figure 6-3 Side Cover Locations
Removing and Replacing a Side Cover
145