HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 162

Removing a Slimline DVD Drive, Removing and Replacing a Dual Slimline DVD Carrier

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 162 highlights

Removing a Slimline DVD Drive 1. To remove the DVD drive, press the drive release mechanism to release the drive from the drive bay. 2. Slide the drive out of the DVD carrier. Replacing a Slimline DVD Drive • Slide the drive into the DVD carrier until it clicks into place. Removing and Replacing a Dual Slimline DVD Carrier The Slimline DVD carrier is located in the front of the chassis. The system power to this component must be removed before attempting to remove or replace it. Refer to "Powering Off Hardware Components and Powering On the Server" (page 142) for more information. The carrier holds two Slimline DVDs. The carrier has 2 SCSI-to-IDE converter PCAs that enable the Slimline DVDs to be hot-pluggable CRUs. CAUTION: Observe all ESD safety precautions before attempting this procedure. Failure to follow ESD safety precautions could result in damage to the server. Figure 6-24 Slimline DVD Carrier Location Carrier and Slimline DVD Removing a Slimline DVD Carrier To remove the carrier, use the following procedure: 1. Depress the front locking latch to loosen the carrier from the chassis. 2. Partially slide the carrier out. 3. Disengage the cables from the rear of the carrier. 4. Completely slide the carrier from the chassis. 162 Removing and Replacing Components

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
Removing a Slimline DVD Drive
1.
To remove the DVD drive, press the drive release mechanism to release the drive from the
drive bay.
2.
Slide the drive out of the DVD carrier.
Replacing a Slimline DVD Drive
•
Slide the drive into the DVD carrier until it clicks into place.
Removing and Replacing a Dual Slimline DVD Carrier
The Slimline DVD carrier is located in the front of the chassis. The system power to this component
must be removed before attempting to remove or replace it. Refer to
“Powering Off Hardware
Components and Powering On the Server” (page 142)
for more information.
The carrier holds two Slimline DVDs. The carrier has 2 SCSI-to-IDE converter PCAs that enable
the Slimline DVDs to be hot-pluggable CRUs.
CAUTION:
Observe all ESD safety precautions before attempting this procedure. Failure to
follow ESD safety precautions could result in damage to the server.
Figure 6-24 Slimline DVD Carrier Location
Carrier
and Slimline
DVD
Removing a Slimline DVD Carrier
To remove the carrier, use the following procedure:
1.
Depress the front locking latch to loosen the carrier from the chassis.
2.
Partially slide the carrier out.
3.
Disengage the cables from the rear of the carrier.
4.
Completely slide the carrier from the chassis.
162
Removing and Replacing Components