HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 53

Table 3-1 Wheel Kit Packing List, Tools Required for Installation, WARNING

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Table 3-1 Wheel Kit Packing List (continued) Part Number A6753-04006 A6753-04007 0515-2478 A6093-44013 Not Applicable Description Quantity Left front caster assembly 1 Left rear caster assembly 1 M4 x 0.7 8mm T15 steel zinc machine screw (Used to attach 4 each caster to the chassis) Plywood unloading ramp 1 Phillips head wood screw (Used to attach the ramp to the 2 pallet) Tools Required for Installation The following list provides the installer with the recommended tools to perform the wheel kit installation. • Diagonal side cutters • Safety glasses • Torx screwdriver with T-15 bit • Phillips head screwdriver WARNING! Wear protective glasses while cutting the plastic bands around the shipping container. These bands are under tension. When cut, they can spring back and cause serious eye injury. Use the following procedure to install the wheel kit. 1. Cut and remove the polystrap bands securing the HP server to the pallet. 2. Lift the carton top from the cardboard tray resting on the pallet. 3. Remove the bezel kit carton and the top cushions from the pallet. Figure 3-10 Component Locations Top Cushions Cardboard Tray Bezel Kit 4. Unfold bottom cardboard tray. 5. Carefully tilt the server and place one of the foam blocks (A6093-44002) under the left side of the server. Do not remove any other cushions until instructed to do so. Wheel Kit Installation 53

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
Table 3-1 Wheel Kit Packing List
(continued)
Quantity
Description
Part Number
1
Left front caster assembly
A6753-04006
1
Left rear caster assembly
A6753-04007
4
M4 x 0.7 8mm T15 steel zinc machine screw (Used to attach
each caster to the chassis)
0515-2478
1
Plywood unloading ramp
A6093-44013
2
Phillips head wood screw (Used to attach the ramp to the
pallet)
Not Applicable
Tools Required for Installation
The following list provides the installer with the recommended
tools to perform the wheel kit installation.
•
Diagonal side cutters
•
Safety glasses
•
Torx screwdriver with T-15 bit
•
Phillips head screwdriver
WARNING!
Wear protective glasses while cutting the plastic bands around the shipping
container. These bands are under tension. When cut, they can spring back and cause serious eye
injury.
Use the following procedure to install the wheel kit.
1.
Cut and remove the polystrap bands securing the HP server to the pallet.
2.
Lift the carton top from the cardboard tray resting on the pallet.
3.
Remove the bezel kit carton and the top cushions from the pallet.
Figure 3-10 Component Locations
Top Cushions
Cardboard
Tray
Bezel Kit
4.
Unfold bottom cardboard tray.
5.
Carefully tilt the server and place one of the foam blocks (A6093-44002) under the left side
of the server. Do not remove any other cushions until instructed to do so.
Wheel Kit Installation
53