HP rp7440 User Service Guide, Fourth Edition - HP Integrity rx7640 and HP 9000 - Page 77

Configuring LAN Information for the MP, To set the MP LAN IP address

Get HP rp7440 PDF manuals and user guides View all HP rp7440 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 77 highlights

Refer to power cord policies to interpret LED indicators. 3. Log in to the MP: a. Enter Admin at the login prompt. The login is case sensitive. It takes a few moments for the MP prompt to display. If it does not, be sure the laptop serial device settings are correct: 8 bits, no parity, 9600 baud, and na for both Receive and Transmit. Then, try again. b. Enter Admin at the password prompt. The password is case sensitive. The MP Main Menu is displayed: Figure 3-30 MP Main Menu Configuring LAN Information for the MP This section describes how to set and verify the server management processor (MP) LAN port information. LAN information includes the MP network name, the MP IP address, the subnet mask, and the gatway address. This information is provided by the customer. To set the MP LAN IP address: 1. At the MP Main Menu prompt (MP>) enter cm to enter the MP Command. NOTE: If the Command Menu is not shown, enter q to return to the MP Main Menu, then enter cm.. 2. From the MP Command Menu prompt (MP:CM>) enter lc (for LAN configuration). The screen displays the default values and asks if you want to modify them. Write down the information or log it in a file, as it may be required for future troubleshooting. See .Figure 3-31 Cabling and Power Up 77

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
Refer to power cord policies to interpret LED indicators.
3.
Log in to the MP:
a.
Enter
Admin
at the login prompt. The login is case sensitive.
It takes a few moments for the MP prompt to display. If it does not, be sure the laptop
serial device settings are correct: 8 bits, no parity, 9600 baud, and na for both Receive
and Transmit. Then, try again.
b.
Enter
Admin
at the password prompt. The password is case sensitive.
The MP Main Menu is displayed:
Figure 3-30
MP Main Menu
Configuring LAN Information for the MP
This section describes how to set and verify the server management processor (MP) LAN port
information. LAN information includes the MP network name, the MP IP address, the subnet
mask, and the gatway address. This information is provided by the customer.
To set the MP LAN IP address:
1.
At the MP Main Menu prompt (MP>) enter cm to enter the MP Command.
NOTE:
If the Command Menu is not shown, enter
q
to return to the MP Main Menu, then
enter
cm
..
2.
From the MP Command Menu prompt (MP:CM>) enter lc (for LAN configuration).
The screen displays the default values and asks if you want to modify them. Write down
the information or log it in a file, as it may be required for future troubleshooting. See
.
Figure 3-31
Cabling and Power Up
77