IBM 326m Hardware Maintenance Manual - Page 73

power-supply

Get IBM 326m - eServer - 7969 PDF manuals and user guides
UPC - 000435835093
View all IBM 326m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 73 highlights

Power-cord module Power-cord module release a. Press down on the retention clip at the front of the power-cord module and slide the module toward the front of the server until the alignment tab is free of the slot on the side of the server. b. Lift the power-cord module out of the server as far as the power-supply cable permits and set it aside. 5. Remove the DASD fan duct assembly located near the power supply (see illustration in "Replacing a fan assembly" on page 50). Attention: Before removing the power supply, make sure that the round USB cable and the flat ribbon cable are out of the way, to avoid damage. 6. Remove the power supply: a. Disconnect the cables on the power supply. b. Remove the screw holding the power supply to the chassis and slide the power supply toward the front of the server until it disengages from the tabs on the floor of the chassis. To install the new power supply, reverse this procedure, making sure that all cables are routed correctly and do not block the air flow from the fan. Chapter 6. Service replaceable units 63

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Power-cord
module
Power-cord
module release
a.
Press
down
on
the
retention
clip
at
the
front
of
the
power-cord
module
and
slide
the
module
toward
the
front
of
the
server
until
the
alignment
tab
is
free
of
the
slot
on
the
side
of
the
server.
b.
Lift
the
power-cord
module
out
of
the
server
as
far
as
the
power-supply
cable
permits
and
set
it
aside.
5.
Remove
the
DASD
fan
duct
assembly
located
near
the
power
supply
(see
illustration
in
“Replacing
a
fan
assembly”
on
page
50).
Attention:
Before
removing
the
power
supply,
make
sure
that
the
round
USB
cable
and
the
flat
ribbon
cable
are
out
of
the
way,
to
avoid
damage.
6.
Remove
the
power
supply:
a.
Disconnect
the
cables
on
the
power
supply.
b.
Remove
the
screw
holding
the
power
supply
to
the
chassis
and
slide
the
power
supply
toward
the
front
of
the
server
until
it
disengages
from
the
tabs
on
the
floor
of
the
chassis.
To
install
the
new
power
supply,
reverse
this
procedure,
making
sure
that
all
cables
are
routed
correctly
and
do
not
block
the
air
flow
from
the
fan.
Chapter
6.
Service
replaceable
units
63