IBM 326m Hardware Maintenance Manual - Page 86

reassembling

Get IBM 326m - eServer - 7969 PDF manuals and user guides
UPC - 000435835093
View all IBM 326m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 86 highlights

System board screws (7 places) Heat-sink retainer bracket screws (4 places) I/O port screws (4 places) Heat-sink retainer bracket screws (4 places) Locator hole Locator pin 15. Remove the six I/O port screws at the rear of the server. 16. Remove the eight screws that secure the two heat-sink retention modules to the system board. These eight screws also secure the system board to the chassis. 17. Remove the remaining seven screws on the system board that secure the system board to the chassis. 18. Carefully pull the board out of the server, taking special care not to disturb any surrounding components. To reinstall the board, place it carefully into position and ensure the locator pin engages the locator hole in the system board. Reverse steps 5 on page 75 through 14 on page 75 to replace the components that were removed. Note: When reassembling the components in the server, be sure to route all cables carefully so that they are not exposed to excessive pressure. 76 326m Type 7969: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Heat-sink
retainer bracket
screws (4 places)
Heat-sink
retainer bracket
screws (4 places)
System board
screws (7 places)
Locator pin
I/O port
screws (4 places)
Locator
hole
15.
Remove
the
six
I/O
port
screws
at
the
rear
of
the
server.
16.
Remove
the
eight
screws
that
secure
the
two
heat-sink
retention
modules
to
the
system
board.
These
eight
screws
also
secure
the
system
board
to
the
chassis.
17.
Remove
the
remaining
seven
screws
on
the
system
board
that
secure
the
system
board
to
the
chassis.
18.
Carefully
pull
the
board
out
of
the
server,
taking
special
care
not
to
disturb
any
surrounding
components.
To
reinstall
the
board,
place
it
carefully
into
position
and
ensure
the
locator
pin
engages
the
locator
hole
in
the
system
board.
Reverse
steps
5
on
page
75
through
14
on
page
75
to
replace
the
components
that
were
removed.
Note:
When
reassembling
the
components
in
the
server,
be
sure
to
route
all
cables
carefully
so
that
they
are
not
exposed
to
excessive
pressure.
76
326m
Type
7969:
Hardware
Maintenance
Manual
and
Troubleshooting
Guide