IBM 326m Hardware Maintenance Manual - Page 74

Operator, information

Get IBM 326m - eServer - 7969 PDF manuals and user guides
UPC - 000435835093
View all IBM 326m manuals
Add to My Manuals
Save this manual to your list of manuals

Page 74 highlights

Operator information card Complete the following steps to remove the operator information card. This component is located in the front of the server. Note: v Read "Installation guidelines" on page 29. v Read the safety notices at "Safety information" on page 107. v Read "Handling static-sensitive devices" on page 30. 1. Turn off the server. 2. Disconnect all power cords and external cables from the back of the server; then, remove the server from the rack. 3. Remove the server cover and bezel (see "Removing the cover and bezel" on page 32). 4. Remove the hard disk drive that is in the right-hand bay, if any (see "Installing a hard disk drive" on page 39). 5. Disconnect the operator information card cables from the system board. Tabs Operator information card 6. Gently pull the operator information card forward until it disengages from the two tabs on the chassis, making sure that any cables that are pulled slide smoothly. 7. Disconnect the cables from the rear of the operator information card. To replace the operator information card, connect the two cables to the rear of the card and slide it under the tabs on the chassis until it is firmly anchored. 64 326m Type 7969: Hardware Maintenance Manual and Troubleshooting Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
Operator
information
card
Complete
the
following
steps
to
remove
the
operator
information
card.
This
component
is
located
in
the
front
of
the
server.
Note:
v
Read
“Installation
guidelines”
on
page
29.
v
Read
the
safety
notices
at
“Safety
information”
on
page
107.
v
Read
“Handling
static-sensitive
devices”
on
page
30.
1.
Turn
off
the
server.
2.
Disconnect
all
power
cords
and
external
cables
from
the
back
of
the
server;
then,
remove
the
server
from
the
rack.
3.
Remove
the
server
cover
and
bezel
(see
“Removing
the
cover
and
bezel”
on
page
32).
4.
Remove
the
hard
disk
drive
that
is
in
the
right-hand
bay,
if
any
(see
“Installing
a
hard
disk
drive”
on
page
39).
5.
Disconnect
the
operator
information
card
cables
from
the
system
board.
Operator
information card
Tabs
6.
Gently
pull
the
operator
information
card
forward
until
it
disengages
from
the
two
tabs
on
the
chassis,
making
sure
that
any
cables
that
are
pulled
slide
smoothly.
7.
Disconnect
the
cables
from
the
rear
of
the
operator
information
card.
To
replace
the
operator
information
card,
connect
the
two
cables
to
the
rear
of
the
card
and
slide
it
under
the
tabs
on
the
chassis
until
it
is
firmly
anchored.
64
326m
Type
7969:
Hardware
Maintenance
Manual
and
Troubleshooting
Guide