Intermec PB51 PB50 and PB51 Mobile Printer User Guide - Page 47

Dynamic WEP 802.1x, SSID Network Name

Get Intermec PB51 PDF manuals and user guides View all Intermec PB51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 47 highlights

Chapter 2 - Configuring the Mobile Printer 5 If your wireless access point uses DHCP, select Get TCP/IP parameters automatically. If the access point does not use DHCP, select Use the following TCP/IP parameters and type the device IP Address, Network Mask, Default Router (default gateway), and Name Server (primary DNS server). Click Next. 6 Type the SSID (Network Name). For peer-to-peer access points, select This is an ad hoc network and select the Channel you want to use. The channel setting must be the same on all wireless devices on the ad-hoc network. Click Next. 7 Select the security options required to connect to your wireless network. Click Next. 8 If you selected Static WEP, Dynamic WEP (802.1x), or Wi-Fi Protected Access in Step 7, type the WEP keys or network credentials required for authentication. Click Next. 9 Wait for PrintSet to apply your settings. Click Next, then click Finish to complete the wizard. To set up the printer for wireless communications using a communications program 1 Connect the 8-pin circular DIN connector to the serial port on the printer. 2 Connect the other end of the serial cable to a serial port on the back of your PC or to a serial adapter on your mobile computer. 3 Open a communications program such as HyperTerminal on your PC and configure the following parameters for the serial port: Parameter Baud rate Data bits Parity Stop bits Default Setting 115200 8 None 1 PB50 and PB51 Mobile Printer User Guide 35

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 2 — Configuring the Mobile Printer
PB50 and PB51 Mobile Printer User Guide
35
5
If your wireless access point uses DHCP, select
Get TCP/IP
parameters automatically
. If the access point does not use
DHCP, select
Use the following TCP/IP parameters
and type
the device
IP Address
,
Network Mask
,
Default Router
(default
gateway), and
Name Server
(primary DNS server). Click
Next
.
6
Type the
SSID (Network Name)
. For peer-to-peer access points,
select
This is an ad hoc network
and select the
Channel
you
want to use. The channel setting must be the same on all wireless
devices on the ad-hoc network. Click
Next
.
7
Select the security options required to connect to your wireless
network. Click
Next
.
8
If you selected
Static WEP
,
Dynamic WEP (802.1x)
, or
Wi-Fi
Protected Access
in Step 7, type the WEP keys or network
credentials required for authentication. Click
Next
.
9
Wait for PrintSet to apply your settings. Click
Next
, then click
Finish
to complete the wizard.
To set up the printer for wireless communications using a
communications program
1
Connect the 8-pin circular DIN connector to the serial port on the
printer.
2
Connect the other end of the serial cable to a serial port on the
back of your PC or to a serial adapter on your mobile computer.
3
Open a communications program such as HyperTerminal on your
PC and configure the following parameters for the serial port:
Parameter
Default Setting
Baud rate
115200
Data bits
8
Parity
None
Stop bits
1