Intermec PB51 PB50 and PB51 Mobile Printer User Guide - Page 52

Configuring Wireless Printing Using Fingerprint, To con the printer to use WEP authentication

Get Intermec PB51 PDF manuals and user guides View all Intermec PB51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 52 highlights

Chapter 2 - Configuring the Mobile Printer Configuring Wireless Printing Using Fingerprint Use the following procedures to configure your printer with Fingerprint for wireless printing. To configure the printer to use WEP authentication 1 Send the following commands to login as an administrator and set the SSID: run"su -p pass admin" setup write "wlan","uart1:" setup "wlan","SSID","xxxxx" where xxxxx can be from 0 to 32 ASCII characters, not including the double quote. Note: The default password for logging in as an admin is "pass." If you have changed the password, you will need to use your password instead of "pass." 2 Send the following commands to configure the WEP keys. The following example sets WEP key 1 to 1234 and enables WEP key 1. setup "wlan","WEP1","0x0001020304" setup "wlan",".WEP_KEY","1" setup "wlan","ACTIVE","1" setup write "wlan","uart1:" To configure the printer to use WPA-PSK or WPA2-PSK mode 1 Send the following commands to login as an administrator and set the SSID: run"su-p pass admin" setup write "wlan","uart1:" setup "wlan","SSID","xxxxx" where xxxxx can be from 0 to 32 alphanumeric characters. 2 Send one of the following WPA/WPA2 ON commands to turn on WPA or WPA2 authentication. Send the WPA-PSK or WPA2-PSK command to set a pre-shared key: setup "wlan","WPA","ON" setup "wlan","WPA2","ON" setup "wlan","WPA_PSK","xxxxxxxxxx" setup "wlan","ACTIVE","1" setup write "wlan","uart1:" where xxxxxxxxxx is a value between 8 and 64 characters. 40 PB50 and PB51 Mobile Printer User Guide

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 2 — Configuring the Mobile Printer
40
PB50 and PB51 Mobile Printer User Guide
Configuring Wireless Printing Using Fingerprint
Use the following procedures to configure your printer with
Fingerprint for wireless printing.
To configure the printer to use WEP authentication
1
Send the following commands to login as an administrator and set
the SSID:
run"su -p pass admin"
setup write "wlan","uart1:"
setup "wlan","SSID",
"xxxxx
"
where
xxxxx
can be from 0 to 32 ASCII characters, not including
the double quote.
2
Send the following commands to configure the WEP keys. The
following example sets WEP key 1 to 1234 and enables WEP key 1.
setup "wlan","WEP1","0x0001020304"
setup "wlan",".WEP_KEY","1"
setup "wlan","ACTIVE","1"
setup write "wlan","uart1:"
To configure the printer to use WPA-PSK or WPA2-PSK mode
1
Send the following commands to login as an administrator and set
the SSID:
run"su-p pass admin"
setup write "wlan","uart1:"
setup "wlan","SSID","
xxxxx
"
where
xxxxx
can be from 0 to 32 alphanumeric characters.
2
Send one of the following WPA/WPA2 ON commands to turn on
WPA or WPA2 authentication. Send the WPA-PSK or WPA2-PSK
command to set a pre-shared key:
setup "wlan","WPA","ON"
setup "wlan","WPA2","ON"
setup "wlan","WPA_PSK","
xxxxxxxxxx
"
setup "wlan","ACTIVE","1"
setup write "wlan","uart1:"
where
xxxxxxxxxx
is a value between 8 and 64 characters.
Note:
The default password for logging in as an admin is “pass.”
If you have changed the password, you will need to use your
password instead of “pass.”