Intermec PB51 PB50 and PB51 Mobile Printer User Guide - Page 53

To con the Printer to use WPA or WPA2 Enterprise mode

Get Intermec PB51 PDF manuals and user guides View all Intermec PB51 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 53 highlights

Chapter 2 - Configuring the Mobile Printer To configure the Printer to use WPA or WPA2 Enterprise mode 1 Send the following commands to login as an administrator and set the SSID: run"su-p pass admin" setup write "wlan","uart1:" setup "wlan","SSID","xxxxx" where xxxxx can be from 0 to 32 alphanumeric characters. 2 Send one of the following WPA/WPA2 ON commands to set up WPA-802.1x or WPA2-802.1x authentication. You should also send the WPA_PSK command that does not contain a value: setup "wlan","WPA","ON" setup "wlan","WPA2","ON" setup "wlan","WPA_PSK","" setup write "wlan","uart1:" • To view the 802.1x values, send this command: setup write "8021x","uart1:" 3 Send these commands to configure the EAP_TYPE: setup "8021x","EAP_TYPE","xxxx" where xxxx can be OFF, LEAP, PEAP, or TTLS. setup "8021x",".EAP_USER","xxxx" setup "8021x","EAP_PASS","xxxx" where xxxx is the unique username and the unique password for this protocol. 4 If you are using TTLS, you may need to send this command to set the TTLS outer name: setup "8021x","TTLS_USER","xxxx" where xxxx is the outer name. 5 If you are using certificates for authentication, here are some commands you may need to use. • Send the following commands to set a certificate and enable validation: setup "8021x","CA_CERT","c:/test.pfx@export" setup "8021x","VALIDATE","ON" where c:/test.pfx is the location and name of the certificate and export is the passphrase. PB50 and PB51 Mobile Printer User Guide 41

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
Chapter 2 — Configuring the Mobile Printer
PB50 and PB51 Mobile Printer User Guide
41
To configure the Printer to use WPA or WPA2 Enterprise mode
1
Send the following commands to login as an administrator and set
the SSID:
run"su-p pass admin"
setup write "wlan","uart1:"
setup "wlan","SSID","
xxxxx
"
where
xxxxx
can be from 0 to 32 alphanumeric characters.
2
Send one of the following WPA/WPA2 ON commands to set up
WPA-802.1x or WPA2-802.1x authentication. You should also
send the WPA_PSK command that does not contain a value:
setup "wlan","WPA","ON"
setup "wlan","WPA2","ON"
setup "wlan","WPA_PSK",""
setup write "wlan","uart1:"
•
To view the 802.1x values, send this command:
setup write "8021x","uart1:"
3
Send these commands to configure the EAP_TYPE:
setup "8021x","EAP_TYPE","
xxxx
"
where
xxxx
can be OFF, LEAP, PEAP, or TTLS.
setup "8021x",".EAP_USER","
xxxx
"
setup "8021x","EAP_PASS","
xxxx
"
where
xxxx
is the unique username and the unique password for
this protocol.
4
If you are using TTLS, you may need to send this command to set
the TTLS outer name:
setup "8021x","TTLS_USER","
xxxx
"
where
xxxx
is the outer name.
5
If you are using certificates for authentication, here are some
commands you may need to use.
•
Send the following commands to set a certificate and enable
validation:
setup "8021x","CA_CERT","
c:/test.pfx
@
export
"
setup "8021x","VALIDATE","ON"
where
c:/test.pfx
is the location and name of the certificate and
export
is the passphrase.