JVC BR-DV6000U User Manual - Page 24

Alarm display, Display, Description

Page 24 highlights

ON-SCREEN DISPLAY - Alarm display - Ⅵ Alarm display : An alarm message is displayed at the following positions when there has been an operation error or when BR-DV6000 is not in good condition, e.g., dirty head. 3 2K CH- 1 / 2 SP0 0 0m i n A HEAD CL EAN I NG REQU I RED ! B NO DV S I GNA L 03 / 04 / 03 11 : 20 : 00 S T ANDBY -OF F TCR 0 2 : 0 0 : 0 0 : 0 0 ● "A" display : The state of BR-DV6000 is displayed. It continues to be displayed until the error state is corrected. This display is not affected by the setting of the display mode. Display LOW VOLTAGE Description The voltage of the DC power source is low. If the operation continues, it enters the Operate OFF mode. HEAD CLEANING REQUIRED! The video head is dirty. Clean it with the head-cleaning tape exclusively for BR- DV6000. (☞ Page 8) If the head is clogged, it is detected in the PLAYBACK mode and this message is displayed. OVERHEATING! The temperature inside BR-DV6000 has exceeded the stated value. Disconnect the power and place it at a cool place. If this message is displayed again, BR-DV6000 could be defective. Consult your JVC-authorized service agent. ● "B" display : Messages for incorrect operation are displayed for about 3 seconds. They are displayed when the DISPLAY mode is ON or AUTO. Display Description INVALID TAPE! Data tape for PCs or DVC PRO tape is used. The cassette tape will be automatically ejected. LP TAPE! The user attempted to play back a tape recorded in the LP mode. BR-DV6000 cannot record or play in the LP mode. NO DV SIGNAL The user attempted to record without DV signal input. COPY INHIBIT The user attempted to record copy-guarded signals. REC INHIBIT The user attempted to record on a tape that is not ready for recording (the rear switch is set to SAVE). REC INHIBIT (NTSC/PAL) The user attempted to record analog signals when PB/DV IN in the SYSTEM (2/2) Menu is set to PAL. 24

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106

24
ON-SCREEN DISPLAY
– Alarm display –
±
Alarm display
:
An alarm message is displayed at the following positions when there has
been an operation error or when BR-DV6000 is not in good condition,
e.g., dirty head.
“A” display
:
The state of BR-DV6000 is displayed. It continues to be displayed until the error state is
corrected. This display is not affected by the setting of the display mode.
“B” display
:
Messages for incorrect operation are displayed for about 3 seconds.
They are displayed when the DISPLAY mode is ON or AUTO.
Display
Description
LOW VOLTAGE
HEAD CLEAN-
ING REQUIRED!
OVERHEATING!
The voltage of the DC power source is low. If the operation continues, it enters
the Operate OFF mode.
The video head is dirty. Clean it with the head-cleaning tape exclusively for BR-
DV6000. (
Page 8)
If the head is clogged, it is detected in the PLAYBACK mode and this message
is displayed.
The temperature inside BR-DV6000 has exceeded the stated value.
Disconnect the power and place it at a cool place. If this message is displayed
again, BR-DV6000 could be defective.
Consult your JVC-authorized service agent.
INVALID TAPE!
LP TAPE!
NO DV SIGNAL
COPY INHIBIT
REC INHIBIT
REC INHIBIT
(NTSC/PAL)
Data tape for PCs or DVC PRO tape is used.
The cassette tape will be automatically ejected.
The user attempted to play back a tape recorded in the LP mode.
BR-DV6000 cannot record or play in the LP mode.
The user attempted to record without DV signal input.
The user attempted to record copy-guarded signals.
The user attempted to record on a tape that is not ready for recording (the rear
switch is set to SAVE).
The user attempted to record analog signals when PB/DV IN in the SYSTEM
(2/2) Menu is set to PAL.
Display
Description
32K
CH– 1 / 2
0
SP
min
00
HEAD
CLEAN I NG
REQU I RED !
NO DV S I GNAL
03/04/03
STANDBY
-
OFF
11:20:00
TCR
02:00:00:00
A
B