Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 60

For each tenth 0.1 that you increase the setting, the, image will be moved 0.1 mm to the right.

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 60 highlights

Section 6 COPY DEFAULT SETTINGS 20 21 Prior to performing the adjustment procedure, it is necessary to use the Document Processor to make copies in a standard copy mode in order to check the amount of skewed feed that is produced. This procedure assumes that you are using the pattern that is printed out using the "F27" default item (Upper Drawer Skewed Feed Adjustment) as an original. (F30) Select a standard copy mode and set the original in the Document Processor. Set the original into the Document Processor in the direction shown in the illustration and make a copy. 25 If the result is as shown in example (1), increase the setting. If the result is as shown in example (2), decrease the setting. + (1) - (2) 22 23 Refer to steps 1 and 2 and access the actual "F30" default item. Press the Recall%/Enter key. NOTE For each tenth (0.1) that you increase the setting, the image will be moved 0.1 mm to the right. 26 Press the Recall%/Enter key. The operation panel will return to the display in step 2. 27 Press the Reset/Power key. The copier will return to a copy-ready state. 24 Fold the printed sheet (that you made in step 21) up the middle and compare the true center with the printed center line. (printed center line) NOTE Use the Document Processor to make another copy and, if further adjustment is necessary, repeat steps 22 through 27. 6-10

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Section 6
COPY DEFAULT SETTINGS
6-10
20
Prior to performing the adjustment procedure, it is
necessary to use the Document Processor to make copies in
a standard copy mode in order to check the amount of
skewed feed that is produced.
This procedure assumes that you are using the pattern that
is printed out using the “F27” default item (Upper Drawer
Skewed Feed Adjustment) as an original.
(F30)
21
Select a standard copy mode and set the original in the
Document Processor. Set the original into the Document
Processor in the direction shown in the illustration and
make a copy.
22
Refer to steps 1 and 2 and access the actual “F30” default
item.
23
Press the Recall%/Enter key.
24
Fold the printed sheet (that you made in step 21) up the
middle and compare the true center with the printed center
line.
25
If the result is as shown in example
(1)
, increase the
setting. If the result is as shown in example
(2)
, decrease
the setting.
NOTE
For each tenth (0.1) that you increase the setting, the
image will be moved 0.1 mm to the right.
26
Press the Recall%/Enter key. The operation panel will
return to the display in step 2.
27
Press the Reset/Power key. The copier will return to a
copy-ready state.
NOTE
Use the Document Processor to make another copy and,
if further adjustment is necessary, repeat steps 22
through 27.
(printed center line)
(1)
(2)
+
–