Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 63

OPTIONAL EQUIPMENT, Document Processor

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 63 highlights

Section 7 OPTIONAL EQUIPMENT Document Processor Automatically feeds and scans multiple sheet-originals one by one. Names of parts (3)(2) (1) (4) (5) Acceptable originals • Use sheet originals only • Paper weight: 50 g/m² - 120 g/m² • Sizes: 8 1/2" × 14" - 5 1/2" × 8 1/2", and Oficio II (Inch Specification) A4 - A5R, and Folio (Metric Specification) • Number which can be set at one time: 50 sheets (50 g/m² - 80 g/m²) Notes on acceptable documents Be sure NOT to use the following as originals in the Document Processor. In addition, originals with punched holes or perforations should be set so that the edge of the paper with the holes or perforations is facing away from the direction of insertion into the Document Processor. • OHP film or other transparencies. • Soft originals such as carbon or vinyl paper, or other originals that are curled, wrinkled or creased. • Irregularly shaped originals, wet originals, or originals that have adhesive tape or glue on them. • Originals bound with clips or staples. (If you must use such originals, be sure to remove the clips or staples, and straighten any curls, wrinkles or creases, before setting them in the Document Processor. Failure to do so may result in the originals being misfed.) • Originals with cut-out sections or that have a slippery surface on either side. • Originals on which any correction fluid is still wet. • Originals with strong folds. (If you must use such originals, be sure to smooth out the folds before setting them in the Document Processor. Failure to do so may result in the originals being misfed.) IMPORTANT! Be sure that the Document Processor is closed whenever transporting the copier. (1) Original table (Set originals to be copied on this table.) (2) Original insert guides (Align these guides to fit the width of the originals to be copied.) (3) Left cover (Open this cover if an original jam occurs.) (4) Original eject table (Originals that have been copied are ejected and stored here.) (5) Ejection extension (Open this extension when using larger sized originals such as 8 1/2" × 13" (Oficio II), 8 1/2" × 14" (Legal) and Folio.) 7-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
7-1
Section 7
OPTIONAL EQUIPMENT
Document Processor
Automatically feeds and scans multiple sheet-originals one by one.
Acceptable originals
•
Use sheet originals only
•
Paper weight: 50 g/m² – 120 g/m²
• Sizes:
8
1/2
" × 14" – 5
1/2
" × 8
1/2
", and Oficio II (Inch Specification)
A4 – A5R, and Folio (Metric Specification)
•
Number which can be set at one time: 50 sheets (50 g/m² –
80 g/m²)
Notes on acceptable documents
Be sure NOT to use the following as originals in the Document
Processor. In addition, originals with punched holes or perforations
should be set so that the edge of the paper with the holes or
perforations is facing away from the direction of insertion into the
Document Processor.
•
OHP film or other transparencies.
•
Soft originals such as carbon or vinyl paper, or other originals
that are curled, wrinkled or creased.
•
Irregularly shaped originals, wet originals, or originals that have
adhesive tape or glue on them.
•
Originals bound with clips or staples. (If you must use such
originals, be sure to remove the clips or staples, and straighten
any curls, wrinkles or creases, before setting them in the
Document Processor. Failure to do so may result in the originals
being misfed.)
•
Originals with cut-out sections or that have a slippery surface on
either side.
•
Originals on which any correction fluid is still wet.
•
Originals with strong folds. (If you must use such originals, be
sure to smooth out the folds before setting them in the Document
Processor. Failure to do so may result in the originals being
misfed.)
IMPORTANT!
Be sure that the Document Processor is closed whenever
transporting the copier.
Names of parts
(1)
Original table
(Set originals to be copied on this table.)
(2)
Original insert guides
(Align these guides to fit the width of the originals to be
copied.)
(3)
Left cover
(Open this cover if an original jam occurs.)
(4)
Original eject table
(Originals that have been copied are ejected and stored here.)
(5)
Ejection extension
(Open this extension when using larger sized originals such as
8
1/2
" × 13" (Oficio II), 8
1/2
" × 14" (Legal) and Folio.)
(3)
(2)
(4)
(5)
(1)