Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 70

Removal procedures, Paper jam inside the copier

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 70 highlights

Section 8 TROUBLESHOOTING Removal procedures Paper jam inside the copier NOTE If there are any finished copies on the copy storage table, remove them first before performing this procedure. 1 Open the upper front cover. 4 If the leading edge of the jammed paper is visible, pull it out towards you. If the paper is not visible at all, perform the "Paper jam in a drawer" procedure. If the paper has been fed to the rear of the copier but the leading edge is not visible, perform the "Paper jam in the paper eject section" procedure. 2 Open the front cover. 5 Set the Process Unit into the copier by aligning the pins on both sides of the Process Unit with the guides inside the copier, and then slide the Process Unit all the way back into the copier until it stops. 3 Take the Process Unit out of the copier. 6 Close the front cover. 7 Close the upper front cover. 8-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Section 8
TROUBLESHOOTING
8-4
Removal procedures
Paper jam inside the copier
NOTE
If there are any finished copies on the copy storage table,
remove them first before performing this procedure.
1
Open the upper front cover.
2
Open the front cover.
3
Take the Process Unit out of the copier.
4
If the leading edge of the jammed paper is visible, pull it
out towards you.
If the paper is not visible at all, perform the “
Paper jam in
a drawer
” procedure.
If the paper has been fed to the rear of the copier but the
leading edge is not visible, perform the “
Paper jam in the
paper eject section
” procedure.
5
Set the Process Unit into the copier by aligning the pins on
both sides of the Process Unit with the guides inside the
copier, and then slide the Process Unit all the way back into
the copier until it stops.
6
Close the front cover.
7
Close the upper front cover.