Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 65

Setting originals on the platen, DO NOT leave the Document Processor open

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 65 highlights

Setting originals on the platen When copying from an original which cannot be set in the Document Processor (books, magazines, etc.), lift open the Document Processor and set the original directly on the platen. 1 Lift open the Document Processor. Section 7 OPTIONAL EQUIPMENT 3 Close the Document Processor. IMPORTANT! Before opening the Document Processor, make sure that there are no originals remaining on the original table or the original eject table. If there are any originals left on either table, they may fall off the copier when the Document Processor is opened. 2 Set the original to be copied face-down. Be sure to align the original flush up against the left rear corner of the platen. IMPORTANT! DO NOT put undue pressure on the Document Processor when you close it. Doing so might break the platen glass. NOTE Shadows may appear around the edges and up the middle of copies made from open-faced originals (such as books, etc.). CAUTION DO NOT leave the Document Processor open as there is a danger of personal injury. 7-3

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
Section 7
OPTIONAL EQUIPMENT
7-3
Setting originals on the platen
When copying from an original which cannot be set in the
Document Processor (books, magazines, etc.), lift open the
Document Processor and set the original directly on the platen.
1
Lift open the Document Processor.
IMPORTANT!
Before opening the Document Processor, make sure that
there are no originals remaining on the original table or
the original eject table. If there are any originals left on
either table, they may fall off the copier when the
Document Processor is opened.
2
Set the original to be copied face-down. Be sure to align the
original flush up against the left rear corner of the platen.
3
Close the Document Processor.
IMPORTANT!
DO NOT put undue pressure on the Document Processor
when you close it. Doing so might break the platen glass.
NOTE
Shadows may appear around the edges and up the
middle of copies made from open-faced originals (such as
books, etc.).
CAUTION
DO NOT leave the Document Processor open as
there is a danger of personal injury.