Kyocera KM-1500 KM/CS-1500 Operation Guide Rev-2.0 - Page 67

TROUBLESHOOTING, If one of the following indications is displayed

Get Kyocera KM-1500 PDF manuals and user guides View all Kyocera KM-1500 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 67 highlights

Section 8 TROUBLESHOOTING If one of the following indications is displayed When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure. Indication "E07" appears on the copy quantity/ magnification display "E11" appears on the copy quantity/ magnification display "E12" appears on the copy quantity/ magnification display "E31" appears on the copy quantity/ magnification display "E32" appears on the copy quantity/ magnification display "E70" appears on the copy quantity/ magnification display "E71" appears on the copy quantity/ magnification display Procedure The size of paper registered in the default settings is different than the size of the paper actually used. Check the paper size. Pull out the corresponding drawer and then push it back in to delete the error indications. The Paper Feeder was selected, but the upper drawer is not installed or is not inserted properly. Push the upper drawer securely into the copier. When printing out a list or report, there was no 8 1/2" × 11" or A4 size paper available. Press the Paper Select key to select the source of paper feed and then press the Start key. Print out will be performed onto paper from the selected location. The amount of waste toner in the copier has reach the acceptable limit. Contact your service representative or an authorized service center. The toner container is not installed in the copier. Install the toner container. If the optional Document Processor is installed on your copier, there are originals remaining on the original table. Remove the originals, reset them on the original table and try to copy again. The copier will attempt to make copies from any originals that remain uncopied. Reset all of the originals on the original table and try to copy again. Reference Page 3-1 - - - 9-2 - - 8-1

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
8-1
Section 8
TROUBLESHOOTING
When any of the following indications appears on the copy quantity/magnification display, perform the corresponding procedure.
If one of the following indications is displayed
Indication
Procedure
Reference
Page
“E07” appears on the copy quantity/
magnification display
The size of paper registered in the default settings is different than the
size of the paper actually used. Check the paper size.
Pull out the corresponding drawer and then push it back in to delete the
error indications.
3-1
“E11” appears on the copy quantity/
magnification display
The Paper Feeder was selected, but the upper drawer is not installed or is
not inserted properly.
Push the upper drawer securely into the copier.
—
“E12” appears on the copy quantity/
magnification display
When printing out a list or report, there was no 8
1/2
" × 11" or A4 size
paper available.
Press the Paper Select key to select the source of paper feed and then
press the Start key. Print out will be performed onto paper from the
selected location.
—
“E31” appears on the copy quantity/
magnification display
The amount of waste toner in the copier has reach the acceptable limit.
Contact your service representative or an authorized service center.
—
“E32” appears on the copy quantity/
magnification display
The toner container is not installed in the copier.
Install the toner container.
9-2
“E70” appears on the copy quantity/
magnification display
If the optional Document Processor is installed on your copier, there are
originals remaining on the original table.
Remove the originals, reset them on the original table and try to copy
again.
—
“E71” appears on the copy quantity/
magnification display
The copier will attempt to make copies from any originals that remain
uncopied.
Reset all of the originals on the original table and try to copy again.
—