Lexmark 2380 Service Manual - Page 131
Repair Information 4-57, Notes On Replacement, installing the large idler gear
 |
View all Lexmark 2380 manuals
Add to My Manuals
Save this manual to your list of manuals |
Page 131 highlights
Notes On Replacement: • Take care not to break the two latches [6] on the side frame that latch to the paper guide. • Be sure both ends of the paper separator are correctly in the mounting holes. • Use the new slider cam, if one is included with the new side frame; the old slider cam will not work properly although it may seem to fit. • The hub side of all gears goes toward the side frame. While installing the large idler gear, the slider should be in the outer position. The conical side of the gear goes toward the side frame. The lower feed roll gear may be a very tight fit. • 238X-001 - Be sure the head gap sensor is in the correct position while installing the paper feed motor plate. Repair Information 4-57
-
1 -
2
-
3
-
4
-
5
-
6
-
7
-
8
-
9
-
10
-
11
-
12
-
13
-
14
-
15
-
16
-
17
-
18
-
19
-
20
-
21
-
22
-
23
-
24
-
25
-
26
-
27
-
28
-
29
-
30
-
31
-
32
-
33
-
34
-
35
-
36
-
37
-
38
-
39
-
40
-
41
-
42
-
43
-
44
-
45
-
46
-
47
-
48
-
49
-
50
-
51
-
52
-
53
-
54
-
55
-
56
-
57
-
58
-
59
-
60
-
61
-
62
-
63
-
64
-
65
-
66
-
67
-
68
-
69
-
70
-
71
-
72
-
73
-
74
-
75
-
76
-
77
-
78
-
79
-
80
-
81
-
82
-
83
-
84
-
85
-
86
-
87
-
88
-
89
-
90
-
91
-
92
-
93
-
94
-
95
-
96
-
97
-
98
-
99
-
100
-
101
-
102
-
103
-
104
-
105
-
106
-
107
-
108
-
109
-
110
-
111
-
112
-
113
-
114
-
115
-
116
-
117
-
118
-
119
-
120
-
121
-
122
-
123
-
124
-
125
-
126 -
127 -
128 -
129 -
130 -
131 -
132 -
133 -
134 -
135 -
136 -
137
-
138
-
139
-
140
-
141
-
142
-
143
-
144
-
145
-
146
-
147
-
148
-
149
-
150
-
151
-
152
-
153
-
154
-
155
-
156
-
157
-
158
-
159
-
160
-
161
-
162
-
163
-
164
-
165
-
166
-
167
-
168
-
169
-
170
-
171
-
172
-
173
-
174
-
175
-
176
-
177
-
178
-
179
-
180
-
181
-
182
-
183
-
184
-
185
-
186
-
187
-
188
-
189
-
190
-
191
-
192
-
193
-
194
-
195
-
196
-
197
-
198
-
199
-
200
-
201
-
202
-
203
-
204
 |
 |
Repair Information 4-57
Notes On Replacement:
•
Take care not to break the two latches [
6
] on the side frame that
latch to the paper guide.
•
Be sure both ends of the paper separator are correctly in the
mounting holes.
•
Use the new slider cam, if one is included with the new side
frame; the old slider cam will not work properly although it may
seem to fit.
•
The hub side of all gears goes toward the side frame. While
installing the large idler gear, the slider should be in the outer
position. The conical side of the gear goes toward the side
frame. The lower feed roll gear may be a very tight fit.
•
238X-001
-
Be sure the head gap sensor is in the correct
position while installing the paper feed motor plate.