Lexmark 2380 Service Manual - Page 55

POST Service Check, Diagnostic Information 2-31

Page 55 highlights

FRU 2 Pull Tractor Sensor Action A failed pull tractor sensor can cause Alt + Park/Load not to function. With the tractor in the push position, press Alt+Park/ Load several times while alternately holding down and releasing the left pull tractor actuator. The paper should not park or load when the pull tractor actuator is held down. If it does, go to the "Pull Tractor Sensor Service Check" on page 2-38. POST Service Check FRU Action 1 Power LED If the power LED is not on, go to the "Power Service Check" on page 2-32. 2 Cables A faulty interface cable can cause POST errors. Disconnect the interface cable from the printer and turn the printer off and then on. Check the connections of the short flexible cable and the power cable to the main logic board and sub logic board. Check the condition and continuity of the operator panel cable. 3 Operator Panel If no problem is found, the problem may be in either the operator panel or the main logic board. Replace the operator panel and retest the printer. 4 Main Logic Board Replace the main logic board if necessary. Reset the bidirectional print adjustment; refer to "Bidirectional Print Adjustment" on page 4-5. Diagnostic Information 2-31

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204

Diagnostic Information 2-31
POST Service Check
2
Pull Tractor
Sensor
A failed pull tractor sensor can cause
Alt + Park/Load
not to function. With the
tractor in the push position, press
Alt+Park/
Load
several times while alternately holding
down and releasing the left pull tractor
actuator. The paper should not park or load
when the pull tractor actuator is held down. If it
does, go to the
“Pull Tractor Sensor Service
Check” on page 2-38
.
FRU
Action
1
Power LED
If the power LED is not on, go to the
“Power
Service Check” on page 2-32
.
2
Cables
A faulty interface cable can cause POST
errors. Disconnect the interface cable from the
printer and turn the printer off and then on.
Check the connections of the short flexible
cable and the power cable to the main logic
board and sub logic board.
Check the condition and continuity of the
operator panel cable.
3
Operator Panel
If no problem is found, the problem may be in
either the operator panel or the main logic
board. Replace the operator panel and retest
the printer.
4
Main Logic Board
Replace the main logic board if necessary.
Reset the bidirectional print adjustment; refer
to “Bidirectional Print Adjustment” on page 4-5.
FRU
Action