Lexmark 2380 Service Manual - Page 78

Repeat Steps 5 and 6 and readjust the gap if necessary., insert the 0.40 mm 0.016 in. feeler gauge.

Get Lexmark 2380 - Forms Printer B/W Dot-matrix PDF manuals and user guides View all Lexmark 2380 manuals
Add to My Manuals
Save this manual to your list of manuals

Page 78 highlights

7. Move the carrier so that it is just to the right of the right upper feed roller, approximately 50 mm (2.0 in.) from the right side frame. 8. Using feeler gauges [1] of 0.35 mm and 0.40 mm (0.014 in. and 0.016 in.), move the right carrier bushing [2] forward or backward until the gap between the printhead [3] and platen [4] is between 0.35 mm - 0.40 mm (0.014 in. - 0.016 in.). Note: The gap should be wide enough for the 0.35 mm (0.014 in.) feeler gauge to slide in smoothly without catching, but too narrow to insert the 0.40 mm (0.016 in.) feeler gauge. 9. Repeat Steps 5 and 6 and readjust the gap if necessary. 10. Repeat Steps 7 and 8 and readjust the gap if necessary. 11. Set the form thickness lever to suit the paper thickness you are using. 12. Install the ribbon cartridge and paper. 13. Install the ribbon access cover. 14. Run the self test and check the density of the printing. Repeat procedure if necessary. 4-4

  • 1
  • 2
  • 3
  • 4
  • 5
  • 6
  • 7
  • 8
  • 9
  • 10
  • 11
  • 12
  • 13
  • 14
  • 15
  • 16
  • 17
  • 18
  • 19
  • 20
  • 21
  • 22
  • 23
  • 24
  • 25
  • 26
  • 27
  • 28
  • 29
  • 30
  • 31
  • 32
  • 33
  • 34
  • 35
  • 36
  • 37
  • 38
  • 39
  • 40
  • 41
  • 42
  • 43
  • 44
  • 45
  • 46
  • 47
  • 48
  • 49
  • 50
  • 51
  • 52
  • 53
  • 54
  • 55
  • 56
  • 57
  • 58
  • 59
  • 60
  • 61
  • 62
  • 63
  • 64
  • 65
  • 66
  • 67
  • 68
  • 69
  • 70
  • 71
  • 72
  • 73
  • 74
  • 75
  • 76
  • 77
  • 78
  • 79
  • 80
  • 81
  • 82
  • 83
  • 84
  • 85
  • 86
  • 87
  • 88
  • 89
  • 90
  • 91
  • 92
  • 93
  • 94
  • 95
  • 96
  • 97
  • 98
  • 99
  • 100
  • 101
  • 102
  • 103
  • 104
  • 105
  • 106
  • 107
  • 108
  • 109
  • 110
  • 111
  • 112
  • 113
  • 114
  • 115
  • 116
  • 117
  • 118
  • 119
  • 120
  • 121
  • 122
  • 123
  • 124
  • 125
  • 126
  • 127
  • 128
  • 129
  • 130
  • 131
  • 132
  • 133
  • 134
  • 135
  • 136
  • 137
  • 138
  • 139
  • 140
  • 141
  • 142
  • 143
  • 144
  • 145
  • 146
  • 147
  • 148
  • 149
  • 150
  • 151
  • 152
  • 153
  • 154
  • 155
  • 156
  • 157
  • 158
  • 159
  • 160
  • 161
  • 162
  • 163
  • 164
  • 165
  • 166
  • 167
  • 168
  • 169
  • 170
  • 171
  • 172
  • 173
  • 174
  • 175
  • 176
  • 177
  • 178
  • 179
  • 180
  • 181
  • 182
  • 183
  • 184
  • 185
  • 186
  • 187
  • 188
  • 189
  • 190
  • 191
  • 192
  • 193
  • 194
  • 195
  • 196
  • 197
  • 198
  • 199
  • 200
  • 201
  • 202
  • 203
  • 204
4-4
7.
Move the carrier so that it is just to the right of the right upper
feed roller, approximately 50 mm (2.0 in.) from the right side
frame.
8.
Using feeler gauges [
1
] of 0.35 mm and 0.40 mm (0.014 in. and
0.016 in.), move the right carrier bushing [
2
] forward or
backward until the gap between the printhead [
3
] and platen [
4
]
is between 0.35 mm - 0.40 mm (0.014 in. - 0.016 in.).
Note:
The gap should be wide enough for the 0.35 mm (0.014 in.)
feeler gauge to slide in smoothly without catching, but too narrow to
insert the 0.40 mm (0.016 in.) feeler gauge.
9.
Repeat Steps 5 and 6 and readjust the gap if necessary.
10.
Repeat Steps 7 and 8 and readjust the gap if necessary.
11.
Set the form thickness lever to suit the paper thickness you are
using.
12.
Install the ribbon cartridge and paper.
13.
Install the ribbon access cover.
14.
Run the self test and check the density of the printing. Repeat
procedure if necessary.